515,372 active members
6,451 visitors online
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > Mazak, Mitsubishi, Mazatrol > Mazatrol T-2 Controls Service Tech Needed - Northeast USA
Page 1 of 2 12
Results 1 to 20 of 21
  1. #1
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Hi All,

    We just picked up a Mazak QuickTurn10 Lathe, running Mazatrol T-2 controls, and need a Mazak Tech to come out and service the machine controls. We know that Techs with T2 knowledge may be few and far between. We are open to covering airfare and travel time to the jobsite 2 hours north of Pittsbrugh PA plus service time and per diems.

    Any help and thoughts you have on the topic, please advise.

    Thank you !
    Chuck Ferrell

    Sent from my SM-G892A using Tapatalk

  2. #2
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    What is the actual problem?
    Regards Bob

  3. #3
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Hi Sudsy,

    My dad, a retired machinist, bought this Quickturn 10 and wants it checked out. We have the original books and parameters but it looks like we are missing page 4 of the parameters.

    Neither I nor him know the T2 control system so he wants an orientation on it. The T2 is not too intuitive so any insights we can get will be time and money well spent. The machine is in good condition and hope to crank out some parts on it.

    Below are the parameters we have and need (asterisks) Also, P19 parameter is locked and wont take an entry of 0. Board batteries have been replaced.

    Thanks,
    Chuck


    Sent from my SM-G892A using Tapatalk

  4. #4
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Have you done a reinitialise on the control? This should help you with some info.

    https://www.dropbox.com/s/lu3ohx16hv...grams.pdf?dl=0
    Regards Bob

  5. #5
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    No luck in getting to the file you linked Sudsy.

    Sent from my SM-G892A using Tapatalk

  6. #6
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    I tried the link and it works but PM me your email and I will try and send it that way
    Regards Bob

  7. #7
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Bump....

    Anybody have a good Mazatrol T-2 repair/service tech that you can recommend to me?

    Thank you and have a nice Easter.
    Chuck

    Sent from my SM-G892A using Tapatalk

  8. #8
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    I got your PM and sent the link via email. Hope it works
    Regards Bob

  9. #9

    Join Date
    Apr 2019
    Posts
    2

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Can you check the HDD of your machine? Bad sector may make some parameter can not load.

  10. #10
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Quote Originally Posted by tienkhoa View Post
    Can you check the HDD of your machine? Bad sector may make some parameter can not load.
    The T-2 controls is vintage 1985. No hard drives just analog boards and chips to my knowledge.

    Sent from my SM-G892A using Tapatalk

  11. #11
    Junior Member
    Join Date
    Feb 2015
    Posts
    6

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Hi, I have a lot of expeience with both repairing, programming and runnign a QT10N-T2. Sold mine a few mounths ago.
    I currently running these machines: QuickTurn10ATC-T3, SlantTurn30ATC-T3, Multiplex620-T32-6 (T3 is the same as T2 but with C-axis)
    I could help you to getting it up and runnig as long as there is nothing serius problem with the drives etc but since there is no alarm indicating that I think everything is OK with it.
    I could also educate you in programming and handling it.
    I am located in Sweden and I think we could agree on the costs etc.

  12. #12
    Registered
    Join Date
    Apr 2016
    Posts
    74

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    have you contacted mazak? they are most helpful. should be able to get out to you no problem.
    T-2 is a easy to operate control, once they get you going, im sure you will like it.

  13. #13
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Thank you benganboll, I will reach out to via a PM to discuss.

    Skywalker4, unfortunately Mazak has not been too helpful with an M2 board replacement issue but I will reach out to them for possible recommendations on this T2 setup.

    Sent from my SM-G892A using Tapatalk

  14. #14
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Did you get the link I sent you?
    Regards Bob

  15. #15
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Quote Originally Posted by sudsy View Post
    Did you get the link I sent you?
    Yes, I was able to download the manual Bob, thank you very much. I have shared it with my Dad for his use.

    Sent from my SM-G892A using Tapatalk

  16. #16
    Junior Member
    Join Date
    Sep 2012
    Posts
    129

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Quote Originally Posted by RCRDarth View Post
    Yes, I was able to download the manual Bob, thank you very much. I have shared it with my Dad for his use.

    Sent from my SM-G892A using Tapatalk
    Have you had any luck getting it going??
    Regards Bob

  17. #17
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Quote Originally Posted by sudsy View Post
    Have you had any luck getting it going??
    Sorry Sudsy, just got back on the forum. I am working on this issue as I get time since it is not my machine.


    Anyone know of a good Mazak T2 guy in the Pittsburgh area? I just need to get this machine repaired to help out my dad. PM me if you have any info. Thank you.

    Sent from my SM-G892A using Tapatalk

  18. #18
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Quote Originally Posted by Benganboll View Post
    Hi, I have a lot of expeience with both repairing, programming and runnign a QT10N-T2. Sold mine a few mounths ago.
    I currently running these machines: QuickTurn10ATC-T3, SlantTurn30ATC-T3, Multiplex620-T32-6 (T3 is the same as T2 but with C-axis)
    I could help you to getting it up and runnig as long as there is nothing serius problem with the drives etc but since there is no alarm indicating that I think everything is OK with it.
    I could also educate you in programming and handling it.
    I am located in Sweden and I think we could agree on the costs etc.
    Hi Benganboll,

    Sorry for the very delayed response but I am working on another project. I saw your April 23rd post on my thread for repairing my Dads QT10. If you have interest in helping me remotely with this repair, what would be your hourly fee? Send me a PM or let me know how to reach you.

    Thank you.
    Chuck


    Sent from my SM-G892A using Tapatalk

  19. #19
    Registered
    Join Date
    Nov 2017
    Posts
    16

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Bump, any advice on a good indepedent Mazatrol controls guy in Ohio?

    Sent from my SM-G892A using Tapatalk

  20. #20
    Registered
    Join Date
    Feb 2011
    Posts
    15

    Re: Mazatrol T-2 Controls Service Tech Needed - Northeast USA

    Hi my name is Carmine Moriello from Accurate Machine Repair in New Jersey. For OhioMazak experience tech call Diamond Machine Tool.

Page 1 of 2 12

Similar Threads

  1. Los Angeles Service Tech needed
    By mtc2423 in forum General CNC Machine Related Electronics
    Replies: 0
    Last Post: 01-06-2014, 09:23 PM
  2. Fadal service tech needed, concord ca
    By Ryan Moore in forum Fadal
    Replies: 4
    Last Post: 06-07-2013, 06:39 AM
  3. Mazak Service Tech Needed
    By easymoney in forum Want To Buy...Need help!
    Replies: 4
    Last Post: 03-30-2012, 01:04 AM
  4. Fadal service/tech needed
    By alphaorange in forum Fadal
    Replies: 0
    Last Post: 09-29-2011, 11:38 AM
  5. Mazatrol controls for VMC
    By EliseoMonteverd in forum Mazak, Mitsubishi, Mazatrol
    Replies: 1
    Last Post: 03-15-2008, 05:27 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •