524,266 active members*
2,449 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking Machines > Okuma > pls, is it possible to use g22 for c axis ?
Results 1 to 5 of 5
  1. #1
    Member
    Join Date
    Jun 2015
    Posts
    3127

    pls, is it possible to use g22 for c axis ?

    hello, please, is it possible to use g22 for c axis ?

    i wish to rechuck a part with a side hole, and orientate the hole among x axis / kindly
    Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg

  2. #2
    Registered
    Join Date
    Apr 2009
    Posts
    1043

    Re: pls, is it possible to use g22 for c axis ?

    I don’t believe it is possible because it is a spindle drive and not an axis drive. Have you tried it?
    Experience is what you get just after you needed it.

  3. #3
    Member
    Join Date
    Jun 2015
    Posts
    3127

    Re: pls, is it possible to use g22 for c axis ?

    hy mr wizard no, it didn't work

    Code:
        G29 PC=30 ( 2277-01 ALARM-B DATA WORD torque limit A side 1 )
        G22 PC=25 C+10 F+60(100*5) G94 D+12.5 ( L0 still going )
        G28
    upper torque limit is at 60%

    but look what i found inside error's description ( is like there is possible to use PC and PM ) :

    Code:
    7 ->When it was not C axis connection, PC instruction was done by G22/G23/G29.
    8 ->When it was not M-axis specification, PM instruction was done by G22/G23/G29.
    9 ->PW and WT instructions were designated at the same time by G22.

    i may be missing something, because it did not showed " no-spec alarm " / kindly

    ps : please, what means WT from point 9 ?
    Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg

  4. #4
    Registered
    Join Date
    Apr 2009
    Posts
    1043

    Re: pls, is it possible to use g22 for c axis ?

    I think M110 is not active?
    Experience is what you get just after you needed it.

  5. #5
    Member
    Join Date
    Jun 2015
    Posts
    3127

    Re: pls, is it possible to use g22 for c axis ?

    hello again no, m110 is there, i just did not shared the entire code

    Code:
        G00 X500 Z250
        T909 M110 M960 M808
        G00 C0 X150
        G01 C1 F=60 G94
    
    
        G29 PC=30 ( 2277-01 ALARM-B DATA WORD torque limit A side 1 )
        G22 PC=25 C=10 F=60(100*5) G94 D=12.5 ( L0 still going )
        G28
    
    
        M807
    voila
    Ladyhawke - My Delirium, https://www.youtube.com/watch?v=X_bFO1SNRZg

Similar Threads

  1. Replies: 0
    Last Post: 11-04-2019, 10:07 PM
  2. Replies: 17
    Last Post: 09-11-2017, 10:31 PM
  3. Replies: 0
    Last Post: 04-27-2016, 04:08 PM
  4. Replies: 1
    Last Post: 11-17-2015, 07:37 PM
  5. Replies: 0
    Last Post: 08-04-2013, 05:30 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •