Hitachi Seiki Repair / Service / Support
All,
I have decided after many requests to start doing on-site service locally (in the New England area). I can be contacted via email (PM me with info) and respond very quickly, and if the problems get more intricate, I can offer help by phone. If that doesn't help then I can make the trips. I have been servicing these machines for many years and are familiar with the i80, MX3, LX3, Seicos II & III, Micon II & III, Sigma 16, 18 & 21, Fanuc RC4/RB6 (and many other Fanuc based), J300 and the very fun Lambda 10L/40L controls. I have many parts available as well as software (ladders, EPROM programs, parameters) to help you out in any situation. Contact me anytime; I have helped many many people get their machines up and running both in the US and abroad.
John
Re: Hitachi Seiki Repair / Service / Support
Wayne,
just sent you an email.
John
Quote:
Originally Posted by
wt1635
Best wishes for your venture!
I have a Hitachi Seiki HC400, s/n HC40315, M-16-2 Seicos controller in need of ladder diagram #2685B01.
Here's hoping you might be able to assist me. Contact: Wayne Thompson, System Components, Inc.,
[email protected], 269 637-2191.
Thanks for your time. Wayne
Re: Hitachi Seiki Repair / Service / Support
Hello John,
I have Hitachi VK45 milling machine with seiki seicos M II cn, I have the following messages on the screen : 105 SERVO I/F BUS and when i try to manage the programs 141 DIRECTORY BROKEN. Could you help me please?
Re: Hitachi Seiki Repair / Service / Support
Hello,
did the machine lose the batteries? The DIRECTORY BROKEN is an easy fix, but from what it sounds like you lost some info. Let me know
Re: Hitachi Seiki Repair / Service / Support
Quote:
Originally Posted by
shas595
Hello,
did the machine lose the batteries? The DIRECTORY BROKEN is an easy fix, but from what it sounds like you lost some info. Let me know
Hello, the problems came out after main board repair (machine had problems with Y axes, 012 SERVO ALARM) i dont know the battery state. Do you think that is softW or hardW problem?
Sorry for my poor english
Re: Hitachi Seiki Repair / Service / Support
If you changed the main board, it is likely a software problem. Send me a PM with your email and I will contact you direct
Re: Hitachi Seiki Repair / Service / Support
Hello
I have some problem with my machine.
Model is HC400 Hitachi seiki control fanuc 15MA.
Main board is SEICOS M16-II .
I think the ladder program was gone.
Now machine cannot operate.
I want to see the ladder of my machine.
I'm see some program can use.
But I'm nohave how to get it?
My mail is [email protected]
some body please help me.
Re: Hitachi Seiki Repair / Service / Support
Hello
I have some problem with my machine.
I have a Hitachi Seiki HC400, M-16-2 Seicos controller in need of ladder diagram .
Here's hoping you might be able to assist me. [email protected].
Thanks for your time.
Re: Hitachi Seiki Repair / Service / Support
Hello,
got your message, just sent you an email. Take a look
John
Quote:
Originally Posted by
juyoung
Hello
I have some problem with my machine.
I have a Hitachi Seiki HC400, M-16-2 Seicos controller in need of ladder diagram .
Here's hoping you might be able to assist me.
[email protected].
Thanks for your time.
Re: Hitachi Seiki Repair / Service / Support
Hi there!
If it worth purchasing Hitachi-Seiki VK45 II with Seicos ? Heard some negativices, so i'm in doubt
Re: Hitachi Seiki Repair / Service / Support
Need more info than that. All depend on the condition. They are still serviceable, and parts are getting scarce but there are resources to keep them going. Just have to know where to look!
Re: Hitachi Seiki Repair / Service / Support
Quote:
Originally Posted by
shas595
Need more info than that. All depend on the condition. They are still serviceable, and parts are getting scarce but there are resources to keep them going. Just have to know where to look!
Thanks for a response
The thing is i'm just looking for a CNC machine to buy and there is a good offer on Hitachi Seiki VK45 II 1995year . So i wonder if i will get faults very often or no, regarding to the experience of the owners on this thread. Its my first CNC so i do not want to have it down with repairs all the time. And i'm not from the USA so there will be a problems for me on getting the parts
Re: hitachi seiki turn 40s
Hello
did you ever get this sorted out? I noticed I was not getting notifications of new posts on this thread - sorry for the delay! Let me know if I can help
John
2 Attachment(s)
Re: Hitachi Seiki Repair / Service / Support
Re: Hitachi Seiki Repair / Service / Support
Bob
what are the hard alarm description on the PC. You can manually move the axis off the hard limits via the ballscrew, just turn by hand to get them clear. Have you done that already?
John
Quote:
Originally Posted by
BCMCD1
I have a VS50 with A10M Seicos and had the machine moved. made the mistake of turning on and not manually positioning the axis' It had a hard ride and I have hard stop errors. and (803) on the NC. I also have NC servo system alarm [2A01] and NC alarm {2A05} on the PC. I cant start the servos until I reset the PC. I have a flashing LED on my SL BUs card for communication. Any help would be appreciated to reset the PC alarm. Thank you Bob