pc is dying, is it time for mach 4
My pc is dying or dead. I'm running Mach 3 on my Taig CNC. Trying to find a Windows XP computer today is difficult. I'm thinking of moving to Mach 4. As I understand it, I will need a motion controller as well? Is this all plug and play? Cause I'm better with a hammer then with a computer. :confused: What motion controller works well with Mach 4, Windows 10, and a Gecko 540.
Re: pc is dying, is it time for mach 4
Not the USB smoothstepper!
Sent from my iPhone using Tapatalk
Re: pc is dying, is it time for mach 4
Ethernet smooth stepper works well with Mach4
Re: pc is dying, is it time for mach 4
uC100 plugs into the G540 but I found issues where the two Y axis steppers became out of sync. Never found a solution. Suspected USB which tends to be noisy.
Sent from my iPhone using Tapatalk
Re: pc is dying, is it time for mach 4
Hi,
I've used Mach4 and an Ethernet SmoothStepper for seven years. Its light years ahead of Mach3 IMHO.
When you use an external motion controller like an ESS or UC100 or UC300 or....whatever, it relieve the PC of having to generate pulse streams. PCs are not good at
that at the gest of times. It also required that the PC run a 32bit OS like WindowsXP.
Once you get an external motion controller to do the pulse streams then you can use any PC to run Mach. Note that a Windows 10 machine will run Mach3 OR Mach4
equally well, provided you have an external motion controller.
The simplest way forward for you is to get an external motion controller, ESS recommended ($190USD), and still use Mach3. The ESS has a Mach3 plugin which largely
replicates 'Ports and Pins' tab in Mach3.
Mach4 is quite a different beast and there is a learning curve, which may or may not be what you want. Mach4 is so much more flexible and stable than Mach3 I've never
regretted making the change....not that the first few weeks weren't hard though.
Craig
Re: pc is dying, is it time for mach 4
Joe i did not know i could run mach 3 on a windows 10 pc. sounds like i just need a external motion controller and a new pc
Re: pc is dying, is it time for mach 4
this ESS external motion controller, is it basically a plug and play or does it take a good deal of setup?
Re: pc is dying, is it time for mach 4
Hi,
Quote:
this ESS external motion controller, is it basically a plug and play or does it take a good deal of setup?
It is not plug and play, it does require set-up. This could be done in under half an hour....if you know what you are doing. The problem will be that at first it seems strange
or different to what you are used to so I would guess you will find, as others before have found, that its a learning curve. After some time however, once you become familiar with
it, you'll realise the essential similarities and that its not nearly as hard as you thought initially.
The bottom line is 'do you want to ditch the parallel port so you can use a modern PC or not?' If you do; get yourself an external motion controller, whatever challenge that may be,
OR persevere with the parallel port and a 32 bit OS like XP or Windows7.
Craig
Re: pc is dying, is it time for mach 4
Quote:
Originally Posted by
joeavaerage
The bottom line is 'do you want to ditch the parallel port so you can use a modern PC or not?' If you do; get yourself an external motion controller, whatever challenge that may be,
OR persevere with the parallel port and a 32 bit OS like XP or Windows7.
Craig
Or use a modern PC running Win10 and just add a Parallel port expansion card - even a PC with Win10 64 will run 32bit software (in most cases)
Re: pc is dying, is it time for mach 4
Hi,
Quote:
Or use a modern PC running Win10 and just add a Parallel port expansion card - even a PC with Win10 64 will run 32bit software (in most cases)
Does not work. Machs parallel port is more than just a parallel port, its a motion controller, that is is has to generate pulse steams. No Windows 10 PC can do that.
Craig
Re: pc is dying, is it time for mach 4
Win10 Pro 64bit...
G540 w/ ESS..
Also a C69 PWM speed controller
https://photos.imageevent.com/scl_el...%20control.jpg
Never skips a beat... Running a GlockCNC 750w motor and headstock
Stuart
Re: pc is dying, is it time for mach 4
I just set up my second ESS with a new Windows 10 PC . The PC is a refurbished HP (basically new) I got off ebay for 85 bucks. I run Mach 3 and I'm trying to migrate to Mach 4, but I know Mach 3 so well its hard to invest all the time into Mach 4.
Anyway, it runs flawlessly, took less than 2 hours to get it all downloaded and running.
Re: pc is dying, is it time for mach 4
Hi,
operationally Mach3 and Mach4 are very similar. If you have experience with Mach3 then you should have no bother running jobs on Mach4.
From a set-up and organisational stand point however Mach4 is a new and completely different animal, and as a consequence users whom have Mach3 experience
and expect Mach4 to be identical are disappointed, to the extent that they claim Mach4 is faulty. Most unfortunate but true. In some respects previous Mach3 experience
can count against you when setting up Mach4.....you expect it to behave in a certain way but it does not.
99% of the set-up is already done for three and four axis machines of conventional design, and therefore no customisations are really required. Where you have a machine
of other than conventional design then Mach4's flexibility will serve well, but requires a much greater understanding of Mach4's software organisation and the use of the API and Lua.
These do represent a learning curve, but once mastered mean that Mach4 is light years ahead of Mach3 in my opinion.
Craig
Re: pc is dying, is it time for mach 4
Quote:
Originally Posted by
sclelectronics
This addition of an ESS is confusing me! I get that Win10 doesn't generate the required pulse stream like the old XP and Win7 PC's did, and so the ESS replaces that role via USB from the PC and then outputs via what? the Parallel port ?
The picture doesn't make it any clearer - I assume the G540 is the black box with gold heatsink? And I see a ribbon cable that I guess is plugged into it? Then it gets a bit 'muddy' with about 2 feet of ribbon cable in different directions
and possibly ending up being plugged into the card on the Power Supply. What is this card? - as it only appears to have the single connection (other than power connections?) Then there is another card under the bundle of ribbon cable
which is what ? I spy a USB plug there - which goes where? The PC maybe and is this the ESS - if so what is the card on the power supply?
This maybe entirely logical to the builder / anyone who is up to date with motion control, but i'm not. I either migrate or I build up a new PC and reload XP and live in the stone age!
Re: pc is dying, is it time for mach 4
Nice dissection of my Controller Box...
In the upper left corner of my box is the ESS board.
The ESS is an ethernet connect motion control board!
Bullet proof communication to G540 and motion control.
https://photos.imageevent.com/scl_el.../ESS-Board.jpg
On top of the Main Meanwell Power supply is the C69 PWM speed controller the is connected to Port2 of the ESS.
The small Power supplies you see..
The far one is for dedicated 5vdc for the ESS
The near on is a 12vdc for relays and sensors....
My coolant(micro-drip) is relay pneumatic valve is controlled by an output on the G540!
https://photos.imageevent.com/scl_el...121_174150.jpg