TNC530 PLANE SPATIAL error
I am getting an error when trying to run a program on a DMU160P 5 axis machining centre. Every line with the PLANE SPATIAL command has an error.
This is a program from a new post processor and it the first time we have used the PLANE SPATIAL command, previous programs used CYCLE19.
The lines with errors are 43 , 49 and all other lines in the program with this command.
Has anyone else seen this error? Is it something to do with the control software version?
32 TOOL DEF 21
33 M1
34 ;
35 ; SAFEPOINT
36 M140 MBMAX
37 L Z0 R0 FMAX M91
38 L Y0 R0 FMAX M91
39 L B0 R0 FMAX
40 L X+290. R0 FMAX M91
41 ;
42 ; REALPLANE
43 PLANE SPATIAL SPA0 SPB+90. SPC+154.868 TURN FMAX SEQ+
44 PLANE RESET STAY
45 M128
46 ; L X355.334 Y-335.310 FMAX
47 ; L Z7.525 FMAX
48 M129
49 PLANE SPATIAL SPA0 SPB+90. SPC+154.868 TURN FMAX SEQ+
50 ;
51 CYCL DEF 32.0 TOLERANCE
52 CYCL DEF 32.1 T0.010
53 M126
54 ; KINEMATICS AUTO SET SPATIAL_PLANE
55 L X-7.525 Y+58.904 FMAX M3
56 L Z+485. FMAX M8
Re: TNC530 PLANE SPATIAL error
Update Information No. 4
Releases
The following versions of the NC software were released:
NC software 340 422-03 (export version 340 423-03) - Release: January 2003
NC software 340 480-03 (export version 340 481-03) - Release: January 2003
New features:
The PLANE function defines the position of the machining plane. The TILT MACHINING PLANE soft key appears after pressing the SPECIAL TNC FUNCTIONS soft key. The machining plane can be defined through space angles, Euler angles, projection angles, incremental angles, the entry of three points, or by two vectors. The programming of each function is aided by animated support graphics. This function is only available in conjunction with preset tables. The PLANE function can be programmed after M128.
--------------------------------------
Software options iTNC 530
Software option 1
Cylinder surface interpolation
Feed rate in mm/min
Tilting the working plane
Circular interpolation in 3 axes with tilted working plane
Software option 2
Particularly jerk-free path control
3-D tool compensation through surface-normal vectors
TCPM = Tool Center Point Management
Tool perpendicular to contour
Tool radius compensation vertical to the tool direction
Straight-line interpolation in 5 axes (permit required for export)
Spline interpolation: Execution of splines (third-degree polynomials)
0.5-ms block processing time
Re: TNC530 PLANE SPATIAL error
Thanks for the reply.
I am still working this issue and have a question.
Has anyone come across a problem when using PLANE SPATIAL and FMAX in the same command line?
Re: TNC530 PLANE SPATIAL error
PLANE SPATIAL SPA0 SPB+90. SPC+154.868 TURN FMAX SEQ+
Which axis are going to use? A B or C?
Change the line to PLANE SPATIAL SPB+90.TURN FMAX SEQ+
Re: TNC530 PLANE SPATIAL error
Hi,
I use the Plane Spatial function on my DMU 50 evolution- do NOT delete the angles mentioned here as it would cause a crash!
In my machine "TURN" is not part of the code- I am not familiar with that. You could check if it is whats causing the error (don't try removing it directly- as changes can easily cause crashed. Try it out in test run mode first to see if there is any difference).