Conquest 42 / Fanuc 0-TC / Parameters needed
Hi there,
I have this Conquest 42 with Fanuc 0-TC, serial number is CS-1337-C. It lost parameters when I changed the keypad that was falling apart, and the new one was too tight and obviously kept a couple buttons pushed in when I turned it on...
I contacted Hardinge USA and the service guy sent me 3 files which are '900 stsndard cPAR~1.txt', 'CSGENERAL.TXT.dat' and 'CSMACRO.txt'. He told me they were generic files for that Conquest series and not specific to my machine. Needless to say, it didn't helped me much. Those '900 stsndard cPAR~1.txt' parameters bring alarm 409 and 1008 with the load meter maxing out and AL-34 in the back board. I've narrowed the P917 being the cause of it, and if I leave it as in 'CSGENERAL.TXT.dat', I don't get those alarms. Instead, I get the 1004 alarm even though the brake does work. I can do the zero return, but it doesn't get out of the ZRN state. It doesn't go to 'auto' and ready.
Would someone with comparable machine be able to send me his parameters?
-It has 10’’x14’’ travel, 10 stations turret with 5 live tools, tailstock, tool probe.
-It doesn’t have sub-spindle, part catcher, barfeeder, air blast, hi pressure coolant.
-Not sure if C is full or indexer, we’ve only used it as indexer. The first guy to set it up for us said the backup batteries were dead and parameters gone. I don’t know what he did to make it work. We’ve only been able to use the C as indexer since then though.
Any help would be appreciated. Thank you.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Did you get the 300 series diagnostic bits to tell the brain what kind of machine you have - 10/12 station turret, live tooling/not, tailstock/subspindle, like that?
Regards,
Newc
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Quote:
Originally Posted by
newc
Did you get the 300 series diagnostic bits to tell the brain what kind of machine you have - 10/12 station turret, live tooling/not, tailstock/subspindle, like that?
Regards,
Newc
No, that is not something I got. What Hardinge sent me was the P900's for 0TC, and the P0-P900 + P8000 for generic CS.
If someone has diagnostic parameters, I'd like to take a look a those. And if for 10 station turret / Live tooling / tailstock / tool setter touch probe, that'd be even better. But I'll take a look at anything.
Thanx
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Or would someone have the Fanuc 0-T parameters manual? That could help me I guess.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
You the man. That's 0-TD, but I guess it's worth looking into an try a couple things, see how far off (or not) those are from 0-TC. Thank you.
Quote:
Originally Posted by
Al_The_Man
Emailed over.
Al.
If anyone has 0-TC programming manual, I'm still interested.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
FANUC 0-TC programming manual. I have got.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
The parameters are unique to the machine, compiled by the MTB at design time.
Your only hope is either the OEM or anyone with the same machine.
All I have is the Fanuc parameter manual, but all that gives is the parameter definitions, you also need the 900 option parameters.
Al.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
Hello tsoliz, would you happen to have a set of parameters for the HARDINGE VMC 700? It would be a life saver and greatly appreciated. Thank you in advance!
[email protected]
Regards,
peloflex
Quote:
Originally Posted by
tsoliz
Hello AL , we have a Conquest 42 Fanuc 0T and the batteries died we lost all parameters..
Would you be able to email me the list of nc parameters and the pc dgn 300-900..
I have lots of machine parameters on file but nothing for this machine..Thank you
in advance for your expertise..Tony email
[email protected]
I will reciprocate with any params you may need that i have...ie mori ikegai hyundia seiki..etc
Re: Conquest 42 / Fanuc 0-TC / Parameters needed
I would be very interested in any and all manuals for a Conquest 42 with Fanuc 0T.
Re: Conquest 42 / Fanuc 0-TC / Parameters needed