1 Attachment(s)
VFD HY 2.2kw 220v wiring to UB1 Controller Help
Hello, all
Need some help to setup VFD to UC300ETH-UB1.
Read both manual for UB1 and VFD HY. not much on how to setup wiring.. Most of the information i got from reference on YouTube.
On my diagram hive following wiring set, except the last wire (AH1), which im not sure where it go.
On the VFD pin 1,2 are jump for external connection.
From VFD DCM+FOR connected to UB1 on ON/CM1 relay
The other configuration came up with:
AL1---> VFD---> ACM
AO1--> VFD---> AL
AH1--> VFD---> not sure
If anyone can help me connect this right way., So i don't end up doing damageto VFD or UB1.
Appreciate all the help i can get...
And to everyone be safe out there.
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
UB1 --- VFD
AH1 --- +10
AO1 --- VI
AL1 --- ACM
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
1 Attachment(s)
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Need help with the VFD Parameters.
when i type M3 24000, spindel dosen't move, when i go back to jump VR spindle works fine...
Jump on V1
My parameters in VFD
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD008=220
PD013=00
PD044=1 to use FOR
PD070=? SET FACTORY 0 <---?
PD072=400
PD141=220
PD144=24000
Screenshot of uccnc spidle setting..
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
when i type M3 24000, spindel dosen't move
Try:
S24000
M3
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
6 Attachment(s)
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
So i double checked the parameters my VFD HY 220 2.2kw
My spindle is:
GDZ-80-2 2B
220V 2.2KW 8A
400Hz 24000rpm
VFD parametters
PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007=.50
PD008=220
PD009=13.0
PD010=6.5
PD011=00.0
PD013=00
PD014=20.0
PD015=20.0
PD044=1
PD070=
PD072=400
PD073=0.00
PD141=220
PD142=11.0
PD144=3000
On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
akihiko
So i double checked the parameters my VFD HY 220 2.2kw
My spindle is:
GDZ-80-2 2B
220V 2.2KW 8A
400Hz 24000rpm
VFD parametters
PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007=.50
PD008=220
PD009=13.0
PD010=6.5
PD011=00.0
PD013=00
PD014=20.0
PD015=20.0
PD044=1
PD070=
PD072=400
PD073=0.00
PD141=220
PD142=11.0
PD144=3000
On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?
Yes PD070=0 for 0-10v control ( 1 ) for Pot control
PD011=100
PD073=100
2 Attachment(s)
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
thanks, after the two changes made in VFD parameters below
PD011=100
PD073=100
key in M3 , but run at only 100 slow, make noises
check video uploaded youtube:
https://youtu.be/vI040tahPVc
help.
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
On UCCNC spindle screen, What port is AL1,AO1,AH1 connected too?
Port 4 pin 1, as shown on page 24 of the UB1 manual.
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
hey, ger21
can you help get VFD up and running..
VFD parametters
PD000=0
PD001=1
PD002=1
PD003=400
PD004=400
PD005=400
PD007= 20
PD008=220
PD009=15
PD010=8
PD011=120.0
PD013=00
PD014=12
PD015=12
PD044=1
PD070=0
PD072=400
PD073=120.0
PD141=220
PD142=8.5
PD144=3000
when M3 spindle start, but run at 120,
when type 2400 it run at 100.
if over post, you see picture's /video/ wiring from VFD to UB1.
im hiving a hard time it.
thanks
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
PD072=400
PD073=120.0
You have these backwards
PD072 = 120
PD073 = 400
You also have it wired wrong.
Move the wire from AI to VI.
Measure the voltage between ACM and VI at different speeds. You should get 5V at 12000 rpm, and about 9.8V at 24000 rpm.
If you don't, measure the voltage on the UB1 between AO1 and AL1. You should be seeing the same voltages.
2 Attachment(s)
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
ger21
You have these backwards
PD072 = 120
PD073 = 400
You are confused the Parameters are correct
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
akihiko
thanks, after the two changes made in VFD parameters below
PD011=100
PD073=100
key in M3 , but run at only 100 slow, make noises
check video uploaded youtube:
https://youtu.be/vI040tahPVc
help.
Wiring is incorrect
100Hz =6,000 RPM 120Hz = 7,200 RPM
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
mactec54
You are confused the Parameters are correct
The manual I have is wrong. It shows them both ways in different places. Sorry for the mistake.
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
mactec54
Wiring is incorrect
100Hz =6,000 RPM 120Hz = 7,200 RPM
Which wiring?
the wiring from UB1 to VFD.
AL1 ---> to VFD ---> ACM
AO1 --> to VFD ---> AI
AH1 --> to VFD ---> 10V
or
VFD and Spindle is working fine,
When change PD001 & PD002 back to 0, Operator mode.
The spindle run 0 to 400hz with no problem. i double check the wiring to spindle.
VFD --> Spindle
U --> pin 2
V --> pin 1
W --> pin 3
G --> pin 4 is wire, but not use at this time.
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
As I said before, move the wire from AI to VI.
AI is for current, VI is for 0-10V
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
akihiko
Which wiring?
the wiring from UB1 to VFD.
AL1 ---> to VFD ---> ACM
AO1 --> to VFD ---> AI
AH1 --> to VFD ---> 10V
or
VFD and Spindle is working fine,
When change PD001 & PD002 back to 0, Operator mode.
The spindle run 0 to 400hz with no problem. i double check the wiring to spindle.
VFD --> Spindle
U --> pin 2
V --> pin 1
W --> pin 3
G --> pin 4 is wire, but not use at this time.
As Gerry has said VFD wiring is incorrect just one change VFD ---> VI and to check that you have 0-10v from the control when you make a speed change 5v = around 12000 Rpm so in MDI M3S12000 and check the voltage output before you run the spindle, yo must have the output voltage working before you connect to the spindle
Normally the wiring for the spindle is
Input wiring R T and Ground Terminals
U=Pin 1
V=Pin 2
W=Pin 3
Ground Pin 4
4 Attachment(s)
Re: VFD HY 2.2kw 220v wiring to UB1 Controller Help
Quote:
Originally Posted by
mactec54
As Gerry has said VFD wiring is incorrect just one change VFD ---> VI and to check that you have 0-10v from the control when you make a speed change 5v = around 12000 Rpm so in MDI M3S12000 and check the voltage output before you run the spindle, yo must have the output voltage working before you connect to the spindle
Normally the wiring for the spindle is
Input wiring R T and Ground Terminals
U=Pin 1
V=Pin 2
W=Pin 3
Ground Pin 4
The output AH1 is 5v to 10v
it working now.
M3 run @ 12000 & S24000
i check all my wiring all good.
One question, about stepper driver and setting..
Stepper Drive DM542A and the DIP switch setting
sw1=on , sw2=on , sw3=off = Peak-> 2.84 / RMS->2.03
sw4=off --> Half current
sw5=off , sw6=off , sw7=on , sw8=on -->1600
Stepper motor:
57HD6401-14S 1.8` 3A N1905
The reason im asking is because my AXIS sound a little rough. X, Y, Z,
A picture of UB1 AXIS setting..
maybe i need turn them?
thanks for all the help on the VFD & Spindle guys
