Re: Hitachi Seiki Repair / Service / Support
HITEC-TURN 23SII When we press standby, hydraulic punp starts and shuts off within seconds.
Unable to swith screen from the initial startup menu.
Uncertain if serial no 2320 is actual serial number, plate is elegible this is the
only number on the plate.
Unknown alarms for this one because we can not pass the initial start up screen.
HITEC-TURN 20SII When we press standby, hydraulic pump starts and shuts off within seconds.
These are the alarms we are getting;
392 Z-Axis TG disconnected
390 ServoPack Alarm
310 Power for Servo not supplied
Need help getting these two machines running - We are located in Lula, GA 30554
Re: Hitachi Seiki Repair / Service / Support
Sent you a PM - could be a few things, but need more info before I can get a better idea of what the issue is. take a look. Ill post results when we get it figured out.
John
Re: Hitachi Seiki Repair / Service / Support
Basically what I need is for you to come to Lula Georgia and see if these two machines can be fixed and running.
Call me if you would like 770) 869-0945
Re: Hitachi Seiki Repair / Service / Support
Hi, where in the vm50 I can find the servo endcoder batteries ? I have attached the cabinet photohttps://uploads.tapatalk-cdn.com/201...476336f78c.jpg
1 Attachment(s)
Re: Hitachi Seiki Repair / Service / Support
Dear Jonh,
I need all pararameter , SLbus table, ladder , AB phase , timer , counter, table.
Machine Hitachi seiki model HT20S, control SEICOS LB Mark2 ,
M16-II Ver 7.5.
The baterry died and the machine not ready.
I got the ladder but after putting it with the YUYU software the machine gives me the alarm Z80 CPUAttachment 393886
My email: [email protected]
Re: Hitachi Seiki Repair / Service / Support
Tony
I sent you an email - take a look, will need some more info before i can help out
John
Re: Hitachi Seiki Repair / Service / Support
hello!
What do you mean cleared the RAM? What was the issue that caused you to clear the data? What data did you have to enter?
Re: Hitachi Seiki Repair / Service / Support
Hi friend
The memory of Ram card with A16B 2200 013 was cleard and the service man reinstalled
The Ram card and wrote the program macros.
But now I knew there are problem on tapping cycle and tool changing.
G84 doesn't work. And I have to work with G84.2 when start the program tapping the axis move to forward and when it will backward , the tap will break.and the other problem is on the tool changing. When the program start, the machine have to ready next tool for next op but it doesn't do this.
Help me plz.
Thanks guy.
Re: Hitachi Seiki Repair / Service / Support
Hello
send me a PM with more info
John
Re: Hitachi Seiki Repair / Service / Support
Hi
Is There somebody who have knowledge on a Hicell with complete Nec control ( Nc and servo, only spindle is yaskawa 626VM3)
Thanks.
Re: Hitachi Seiki Repair / Service / Support
Hello!
yes I do - if you want you can PM me your email and Ill help you out!
john
Re: Hitachi Seiki Repair / Service / Support
Few days ago got one scary situation, after probing part on vm50 when I hit cycle start Z Axis instead of going on to Z0 g28 , dropped into the part like it's freefalling , immediately pressed the estop and there was nc servo alarm and 1219 z innefective current over . Had to restart the pc because I couldnt jog the tool of the part. IT looks like the brake on the Z Axis didnt worked as its should ? Is it a sign of the nc control ending it's lifespan or servo ? When the machine idles on the screen I can see 65% when it was jogged to up or 50% when was jogging down Z Axis load . It's 98 model.
Re: Hitachi Seiki Repair / Service / Support
My Hitachi vm50 got Orange screen , machine was staying idle then suddenly black screen appeared and everything was shutdown. Is it something with graphic card ,or LCD ? Or its the NC Control that is down?https://uploads.tapatalk-cdn.com/201...27dbffd1e3.jpg