Printable View
I have problem with my specification :
- win xp sp3
- vfd huanyang
- 5axis circuit board mach3
- mach3 44.66
- pararell port conection
- vfd setting using mactec54 i found this forum. wih pd001 & pd002 value 1
in few days all working well, but change my harddrive and reinstall the winxp and mach3.
load my last xml setting and now all axis work perfectly except my spindle wont work, when i push spindle cw f5 the F0000 on vfd increacing, RPM on mach3 keep 0 and spindle goes off
any solution ?
update i change pd001 = 0 and run, pd0011 from 120 to 0 and hit run..
now mach3 can start stop spindle, and if i set to 5000 speed, the spindle running well but when increase or decrese the speed its always hit max speed.
any suggestion ?
I had a problem on a new install.Quote:
Originally Posted by doraemon_idn
Spindle would run at full speed on startup and stop when set to full speed.
Turned out that when I probed the axis board output it was at 10v when stopped and 0v when full (backwards).
Changing active low / high reversed this to work properly. (0v stopped, 10v full).
If it worked before then it would be something stupid like this.
Why change the vfd settings when it was the PC that was changed?.
The XML won't hold every setting that was user changed.
If PD011 was set at 120 then you can not set it at ( 0 ) you will damage your spindle, a setting of 120 = 7200 RPM a setting of 100 =6000 RPM the minimum Speed for a water cooled spindleQuote:
Originally Posted by doraemon_idn
You first have to have the PWM to Analog 0-10v output working correctly at the Breakout Board, before you connect it to the VFD Drive
I change because pd001=1 cant start stop spindle, so i turn to 0 and hit run so spindle working well with the button, my spindle 2,2kw air cooling spindle, when pd011 set to 100 or 120 wont turnoff and steady at 6600 rpm so i must hit stop button on the vfd to completely stop.Quote:
Originally Posted by mactec54
Please advice for better option, thanks
Wiring is correctQuote:
Originally Posted by doraemon_idn
You have an Air cooed spindle then it will have to be set higher than a water cooed spindle
You first have to get the 0-10v working correctly before you connect it to the VFD Drive, you need to measure the voltage at the Breakout Board In MDI in your control do M3S12000 the Voltage should measure around 5v do different speed settings and check the voltage
Your air cooled spindle has a minimum speed it can be run at or it will over heat so even 130 may still be to low for your spindle
PD011=130
PD073=130
PD001=0 ( 0 ) for KeyPad ( 1 ) for Remote )
PD02=0 ( 1 ) for Remote Control
J1 Jumper Pin 1-2 for Remote Control
You may have other Parameters set incorrect if your spindle speeds don't match what they should be
What other Parameters have you set, post what you have set
Quote:
Originally Posted by mactec54
iam using this parameter, but now i change pd001=1 pd002=1 pd011=130 pd073=130 and now the spindle doesnt workQuote:
Huanyang Mactec54
PD000=0
PD001=0
PD002=0
PD003=400
PD004=400
PD005=400
PD007=20
PD008=120
PD009=15
PD010=8
PD011=120
PD13= 0
PD014 = 10
PD015 =10
PD023=0
PD026=0
PD141=120
PD142=8.5 (matches rating on spindle case)
PD143=2
PD144=3000
PD041=8
PD70=0
PD72=400
PD73=120
The output from the Breakout Board is not working these Parameters PD001 and PD002 setting is for remote controlQuote:
Originally Posted by doraemon_idn
Did you set the J1 Jumper Beside the VFD Drive Terminal Block this has to be in the correct position for Remote Control to work
Is this the voltage of your spindle and the supply voltage what Kw is your spindle motor
PD08=120v
PD141=120v
Ah. Is that the board you're using below?.Quote:
Originally Posted by doraemon_idn
In terms of M3/M4 control I find the relay a bit useless. If you have BOTH M3 & M4 set up to it in Mach as one on and one off it gets confused.
You want M3 going to the relay and M4 going to an output that don't exist, or a second seperate relay.
Then it should switch on/off sort of correctly.
https://www.cnczone.com/forums/attac...2&d=1625610432
Again you don't know what you are even looking at, This is correctly wired to turn the Spindle On and Off there is only one connection the Relay is fine these spindles can only run in one directionQuote:
Originally Posted by dazp1976
Stop wasting peoples time with your Bs posts
Thanks you mactec54 for your help,Quote:
Originally Posted by mactec54
The trouble is on huangyang vfd, i reset factory again and input all parameter you have again its working perfectly. Now i try to calibrate spindle speed with mach3 coz in vfd says 7500 and the mach 8000
Once again thanks for your attention and your dedication
Yes a Reset can sometimes fix these problems, if a Parameter is set incorrect, it only takes ( 1 ) to mess with the systemQuote:
Originally Posted by doraemon_idn
You can use the pulley ratio in Mach3 to adjust the speed to match, do a 12000 RPM and measure the Board output voltage, these Boards there converter is not perfect and most only reach around 9v to 9.8v