Taig 3000 DSLS Mach3 Setup and XML file request
Hey guys, I just bought a Taig Micromill 3000 DSLS with Mach3. My fantastic friend misplaced his microproto CD that included the setup files to run the machine. Do any of you guys have the files available? I'm looking for the following files...
Mach3mill.xml
MPS1024E.set
BackgroundToolpath3.jpg
I tried contacting Microproto directly at [email protected] for the files and the email apparently doesn't exist. It would be a huge help! I have everything ready to go and I just need these files for Mach3.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Sure.... drop me a PM with your e-mail and I'll send them to you.
To make the .XML trouble free for you.... I need to know.
1. 3 Axis or 4 Axis?
2. Are you going to work in inches or MM
Of course, you can set any of this up... but this way it will be basically plug & Play for you. Dan.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Is it possible to get this info still?
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Travis - did you buy your Taig mill new or used? Taig tech support is pretty good, if you're using their system to run it - have you called them for help?
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Quote:
Originally Posted by
Traviss396
I would really appreciate this same information. I can't get this thing running to save my life.
Is this a stock Taig mill?? Let me know some specifics and I am happy to help. Thanks. Dan.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Quote:
Originally Posted by
Ican
Sure.... drop me a PM with your e-mail and I'll send them to you.
To make the .XML trouble free for you.... I need to know.
1. 3 Axis or 4 Axis?
2. Are you going to work in inches or MM
Of course, you can set any of this up... but this way it will be basically plug & Play for you. Dan.
The machine is a microproto 3000 DSLS
It is 4 axis
I will work in mm
Thanks
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Quote:
Originally Posted by
anilchawla
The machine is a microproto 3000 DSLS
It is 4 axis
I will work in mm
Thanks
PM sent.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Sorry to necro an old thread but I wonder if you could send me a copy of that XML also @Ican? Same spec actually: Microproto 3000 DSLS, 4 axis, primarily will work with metric measurements.
I have not used my machine for a few years and when I removed the dust sheet from it today to start it up again the computer that used to run it has failed so I need to set up afresh and it would be great to have the XML as a sanity check.
Much appreciated if you still have the file conveniently to hand.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Ican,
Would it be possible for you to send those files to me, please? I am helping a friend get his going (someone gave it to him without the disk).
1) He has and wants to use the 4th Axis at some point.
2) He will likely use inches.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Quote:
Originally Posted by
Masock
Nevermind. I finally was able to get with someone from Microproto.
Sorry, I have been on the road.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
Sorry to kick start an old thread but I have just inherited a Taig Micromill 3000 DSLS but without the disk of files and info that goes with it.
Is it a possibility to get a copy of those files as well?
Mine is a 4 axis and I will be working in MM.
Thanks in advance.
Re: Taig 3000 DSLS Mach3 Setup and XML file request
You''ll need to buy a seat of Mach3 or 4 to make it run; this isn't free software: https://www.machsupport.com/ Once you've got that installed, all you need is the XML file specific to your machine. Taig will be able to supply that.