2 Attachment(s)
Hertz spindles from Turkey
Hi, i am going to order a spindle motor from this supplier soon. Just wondering if anyone in Australia would like to also order a unit. The shipping for 1-5 units is 150 euro(TNT express)....it makes sense to order more than one:)
https://www.cnczone.com/forums/attac...d=401984&stc=1
https://www.cnczone.com/forums/attac...d=401986&stc=1
Re: Hertz spindles from Turkey
Those prices are fairly cheap! I'm in the USA so I can't get into the buy party so best of luck with finding a partner.
I must ask are you ordering directly from the manufacture or a reseller?
Re: Hertz spindles from Turkey
I was unable to find a re-seller....Initially i planned to buy a Teknomotor but the one i wanted was over $1000 Aud
Thanks.....i might buy a couple anyway, i am sure i will build another machine after this one:)
Re: Hertz spindles from Turkey
I have had 2 of these and Both of them broke on me. I used them to cut aluminum and they couldn’t handle it.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
dillonfitz
I have had 2 of these and Both of them broke on me. I used them to cut aluminum and they couldn’t handle it.
Sent from my iPhone using Tapatalk
Oh no, may i ask how did they break?
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
Oh no, may i ask how did they break?
I had an er20 model and er25. The er 25 actually spun the rotor on the shaft inside the motor. It was just press-fit on so it had no power after it spun. And the er 20 version worked for about 4 months then it finally just quit working. I think the windings burnt up but I’m not 100 percent sure. I switched to a used Colombo and never had another issue.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
Oh no, may i ask how did they break?
I did also use a gmt spindle with a delta drive , I never had an issue with that setup.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
Not good....i wish you replied this a bit earlier cause i ordered a couple of motors a few minutes ago:(
Re: Hertz spindles from Turkey
Do not worry, I have been used Herz spindle three years for now. I cut aluminium and Pom plastic . Spindle is HMB42d 24000 rpm with ceramic bearings.
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
Not good....i wish you replied this a bit earlier cause i ordered a couple of motors a few minutes ago:(
They were great while they worked. The only thing was they were a little noisy. Sounds like a vacuum running. But for the price you can’t expect them to run forever.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
https://uploads.tapatalk-cdn.com/201...2a4df2c335.png
The main problem probably was that the motor can’t handle the er25 collet. The larger tooling is just too hard on the motor.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
I see you even had the better model, the one with the steel in front....they told me to get this type for aluminium
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
jannos
Do not worry, I have been used Herz spindle three years for now. I cut aluminium and Pom plastic . Spindle is HMB42d 24000 rpm with ceramic bearings.
Thanks for the info....i bought a 2.0 Kw and a 1.5 Kw...both HMB120CK and both ER20
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
dillonfitz
Possibly....but why sell the motor with ER25 then??
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
Possibly....but why sell the motor with ER25 then??
That’s what I was thinking.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
My kress router spindle has been going for almost seven years. I cut aluminium, plastic, rubber, timber, brass etc.....but i must add that i never overheat or abuse my tools:)
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
My kress router spindle has been going for almost seven years. I cut aluminium, plastic, rubber, timber, brass etc.....but i must add that i never overheat or abuse my tools:)
I run real machines so Im guilty of being bit rough on my smaller home made machine.
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
dillonfitz
I run real machines so Im guilty of being bit rough on my smaller home made machine.
Sent from my iPhone using Tapatalk
I can understand that....
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
I can understand that....
But I still enjoy the aspect of building a machine and watching it run!
Sent from my iPhone using Tapatalk
Re: Hertz spindles from Turkey
Quote:
Originally Posted by
ericks
I can understand that....
My first home made machine is what led to bigger machines as well.
Sent from my iPhone using Tapatalk