G-Code check...

In format 2.
Simple spot some holes then quick drill. Playing with peck even tho not needed.
Getting an error on the peck cycle - R WORD INVALID (thru simulator not on the fadal itself - yet).
Lines N70, N165

Is there an issue retracting my Z back to my original feed stop height of 0.200" or with the simulator?

Code:

---

%
O1001 (DRILL BRAKE SIDE)
(MACHINE)
(  VENDOR: FADAL)
(  MODEL: VMC-4020HT)
(  DESCRIPTION: FADAL-RWS)


(T1  D=0.375 CR=0. TAPER=90DEG - ZMIN=-0.05 - SPOT DRILL)
(T2  D=0.323 CR=0. TAPER=118DEG - ZMIN=-0.722 - DRILL)


N10 G90 G94 G17
N15 G20
N20 M9
N25 G28 G91 Z0.
N30 G90


(DRILL1)
(*** TOOL CHANGE ***)
(T1  D=0.375 CR=0. - SPOT DRILL)
N35 T1 M6
N40 S1000 M3
N45 G4 P180
N50 G0 E1 X2.7375 Y-0.5
N55 G43 Z0.8 H1
N60 M8
N65 Z0.2
N70 G98 G81 X2.7375 Y-0.5 Z-0.05 R0+0.2 F7.
N75 X5.1125
N80 X7.4875
N85 X14.6125
N90 X16.9875
N95 X19.3625
N100 G80
N105 Z0.8
N110 M5
N115 M9
N120 G28 G91 Z0.
N125 G90


(DRILL2)
N130 M1
(*** TOOL CHANGE ***)
(T2  D=0.323 CR=0. - DRILL)
N135 T2 M6
N140 S1060 M3
N145 G0 E1 X2.7375 Y-0.5
N150 G43 Z0.8 H2
N155 M8
N160 Z0.2
N165 G98 G73 X2.7375 Y-0.5 Z-0.722 R0+0.2 Q0.0807 P0.0065 F3.
N170 X5.1125
N175 X7.4875
N180 X14.6125
N185 X16.9875
N190 X19.3625
N195 G80
N200 Z0.8


N205 M9
N210 G28 G91 Z0.
N215 G90
N220 G53 X1. Y8.5
N225 M30
%

---

The decimal point at the end of the "F" word of the "+" with the "R" word?

I think the decimal point is OK, but I have never seen a R0+0.2 I would expect that to be R0.2

it looks like it should be a macro statement
if you have macro ability change R0+0.2 to R[0+.02] and it should read it
but unless you are going to use a variable to control the R PLANE you should just write it out as Jim has said

Yes, I see the format oddity on the R word. (Fusion 360 Fadal post)

So, reading the Fadal Section 4 document on fixed cycles, the R is suppose to be called such as R0+.xxx so the post is almost doing it right.
I went out this morning and tried the Gcode I posted yesterday and the Fadal digested it fine. The editor simulator just doesn't like it. (GWizard Editor).
The editor has mixed feelings about my G-Code and I have mixed feelings about the editor :)

i just went thru a bunch of my g-code files and F360 post process also creates 'R0+0.2' and i have not had a problem with simulation or running the code on my machine?