Re: Autoleveler not working
Please post your file(s) here, we will try to figure out what the problem is. A screenshot of Autoleveller settings would help too.
You do not have to change anything in Mach3, but you do need to select "Mach3" in Autoleveller setup. Not sure about SafeZ, I don't think I ever changed it from the factory defaults.
2 Attachment(s)
Re: Autoleveler not working
Quote:
Originally Posted by
CitizenOfDreams
Please post your file(s) here, we will try to figure out what the problem is. A screenshot of Autoleveller settings would help too.
You do not have to change anything in Mach3, but you do need to select "Mach3" in Autoleveller setup. Not sure about SafeZ, I don't think I ever changed it from the factory defaults.
Thanks for the info, its good to hear that he problem is some minor issue.
Files attached.
There may be some difference in setting in the generated NC file vs the attached screen shot, since I was playing around with the settings a lot.
Re: Autoleveler not working
In the gcode you attached, Probe Depth is a bit excessive (-20mm), but that should not be a problem. It also has the Safe Height of 0, which should not be a problem either if you zero the Z axis slightly above the stock. Other than that, it looks like a perfectly working probing program (mine looks identical except for the X-Y-Z values).
So at what point do you get the SafeZ messages? What exactly happens when you run the program? Here is the sequence you should see:
- "Attach probe wires" message
- move to safe height, move to bottom left corner, move to Z2
- probe down at high speed
- probe down at a slower speed
- ask for the probe file name
- move around the board and probe 80 points
- "Detach probe wires" message.
Re: Autoleveler not working
Quote:
Originally Posted by
CitizenOfDreams
In the gcode you attached, Probe Depth is a bit excessive (-20mm), but that should not be a problem. It also has the Safe Height of 0, which should not be a problem either if you zero the Z axis slightly above the stock. Other than that, it looks like a perfectly working probing program (mine looks identical except for the X-Y-Z values).
So at what point do you get the SafeZ messages? What exactly happens when you run the program? Here is the sequence you should see:
- "Attach probe wires" message
- move to safe height, move to bottom left corner, move to Z2
- probe down at high speed
- probe down at a slower speed
- ask for the probe file name
- move around the board and probe 80 points
- "Detach probe wires" message.
BTW. Where should I be checking for the messages?
Re: Autoleveler not working
Quote:
Originally Posted by
ZeroBacklash
BTW. Where should I be checking for the messages?
The messages are displayed in Mach3 status line (below the Reset button on the default Mach3 screen).
Re: Autoleveler not working
Quote:
Originally Posted by
CitizenOfDreams
The messages are displayed in Mach3 status line (below the Reset button on the default Mach3 screen).
Ok! so I tried several things more.
First I downloaded the older version of Autoleveler (the standard one).
Then I generated the probe file.
Then on running the first time it gets stuck at some point saying
"Probe ignore activated at call for probe"
If I rewind the code now and run it again.
It retracts to 20mm then moves now say 5mm above the pcb.
And then it moves and pauses only in the y axis at the pauses it should have moved in the Z direction for probing. Instead it stays at the current Z and just moves in the y direction.
I'm trying to single step now, to find the issue however the single steppiing also doesn't work, instead the "Single BLK" LED blinks when I click the "Single BLK" button.
" "
Re: Autoleveler not working
Quote:
Originally Posted by
ZeroBacklash
Then on running the first time it gets stuck at some point saying
"Probe ignore activated at call for probe"
Is your probe working correctly? This error suggests that the probe is already touching at the moment the G31 command is called.
Look at the Digitize signal on the Diagnostic screen. The green light should turn on when the probe is touching the stock.
Re: Autoleveler not working
Quote:
Originally Posted by
CitizenOfDreams
Is your probe working correctly? This error suggests that the probe is already touching at the moment the G31 command is called.
Look at the Digitize signal on the Diagnostic screen. The green light should turn on when the probe is touching the stock.
I did the and the Digitize led does light up when the probe touches.
Also I added M0 statements after each line so that it pauses and I can debug the code. And it did do the first 10 steps correctly.
But after the first 10 steps when I run it from there it tends to go awry. It doesn't seem to honour the G31 Z-5 step instead it just darts in a straight line.
Could it be noise at the probe input that makes it act this way?
Re: Autoleveler not working
Quote:
Originally Posted by
ZeroBacklash
Could it be noise at the probe input that makes it act this way?
It is a good possibility. What does your input circuit for the probe look like?
1 Attachment(s)
Re: Autoleveler not working
Quote:
Originally Posted by
CitizenOfDreams
It is a good possibility. What does your input circuit for the probe look like?
I will open the controller box and see what it looks like.
In the meanwhile this is the controller that I'm currently using.
Re: Autoleveler not working
I checked and the inputs seem to be opto isolated, so that some what minimizes the possibility of noise. I'm running out of ideas now.