hi
i have a turn by:
maker:GILDEMEISTER
type:ctx 200
controller:grundig eltropilot
but all of manuals & language of controller is german
is there anyone help me?
english manual?
excuse me for my english
thanks very much
Printable View
hi
i have a turn by:
maker:GILDEMEISTER
type:ctx 200
controller:grundig eltropilot
but all of manuals & language of controller is german
is there anyone help me?
english manual?
excuse me for my english
thanks very much
hi:Quote:
Originally Posted by russel1712
i have same problem if you found any english catalog .
i need?
tanks
--------------------------------------------------------------------------------
hi
i have a turn by:
maker:GILDEMEISTER
type:ctx 200
controller:grundig eltropilot
but all of manuals & language of controller is german
is there anyone help me?
english manual?
excuse me for my english
thanks very much
Hi,
how are you?
You can change the language of the controller to English, in menu DIAGNOSE.
Regards,
hi:Quote:
Originally Posted by booster05
please expention for me?
how i can change language by DIAGNOSE.
VERY VERY TANKS
hi,
how are you?
On next monday i will give you the steps.
I need to see first in my machine.
Send me one email and i will give you the steps with photos, it's better.
[email protected]
Regards,
Paulo
Hi, help needed
Gildemeister CTX 400 E, with controller Grundig EltroPilot 1190.
Up to speed 900 rpm. spindle stops normally. At higher speed emergency stop occurs and machine coast down without braking. Error message "spindle does not reach setpoint speed".
Thanks to anyone for the advice
Dear Sir,
I had a problem with the drive spindle, when slowed down the velocity of the spindle gave me the error F-41 in the drive.
I had to replace the capacitors in the drive of the spindle.
Attached is the list of errors
Regards,
Paulo
Dear Sir,
Thank you for advice.
Measured capacitance is 1330mkF. But I try replace the capacitors.
Error message
IPO F:710 Channel1: Spindle does not reach setpoint speed
and following
SPS F:253 Spindle drives: General fault
Did anyone have description of cause and remedy.
With best regards
Tony
Quote:
Originally Posted by booster05
I need the manuals too, if anyone have them please PM me or post them here. Thank You!
Dear sirQuote:
Originally Posted by nylas
can you find any document or solution on this case?
best regards
Russell
to change the system controllers language _ Elrtopilot to english :Quote:
Originally Posted by Russell840
first of all, you need to know : Does your controller support english language?
If the answer is yes , you should to go :
Press Operation key ==> Diagnose ==> Press " > " key to go to next page
press " SPRACHE 2 " ( Number 5 key )
The language is English Now.
best regards
Russell
Hi,
I have Gildemeister CTX 200 with Eltro Pilot controller.
Could someone send me an example program for threading?
No I'm moving with G33.
Thank YOu
Peter
Hi!
I just checked this old page.
Do you still need help with EltroPilot?
Regards
Krisztián
HelloQuote:
Originally Posted by stollerk
I am looking for someone who has good knowledge of ELTROPILOT L2 control. I have a Gildemeister MD5 shaft lathe that has been giving problems but just recently is displaying excessive heat alarm P422
Can you help or do you have any information on the alarms
thank you
Regards
dave (1Nipper)
Does nay one know of any people that can support (Electric/electronic) the Grundig ELTROPILOT L2 control. This one is fitted to a Gildemeister MD% Shaft lathe (1992). I have tried Heidenhain UK and DMG Mori in the Uk - both say they do not support this product.
I have a set of manuals, but I dont have any listings for the control alarms that can be displayed - are there any knowledgeable service people that can help? Thank you
Regards
Dave.