Re: Torus Pro with servos and 4th axis
maybe not quite as flattering. I think I isolated the spindle rpm changes to the estop being flaky. The factory one had kinda fallen apart, so I put in another one I had.....it was the flaky one. After removing it and jumpering the wires together, I haven't had any rpm fluctuations like that.
https://www.youtube.com/watch?v=pG8XQRubK1E
Re: Torus Pro with servos and 4th axis
I didn't put the lathe ops here, but I do have vids of them on my channel. This vid is actually pretty cool......at least I like it....especially the chamfering op at the end. :)
https://www.youtube.com/watch?v=FT-wimO5erQ
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
Re: Torus Pro with servos and 4th axis
https://www.youtube.com/watch?v=YPUON2Iq3XA
- - - Updated - - -
Maybe I shouldn't wait 10 months to post what I'm up to. lol
Re: Torus Pro with servos and 4th axis
LOL!!! My last post said I shouldn't wait 10 months to post on here........and now it's been over 3 years. :(
I'll see if I can post a few vids here of stuff dealing with my mill.
How I set tool lengths
https://youtu.be/8CeRj4nC4qI
A chip guard/shield I added to the Z axis
https://youtu.be/-us-zx77ri4
A shelf I made for the coolant
https://youtu.be/0nMwSwVYHV4
What I did for a tank....way better than the laundry soap jug in the shelf video
https://youtu.be/pp38rAuSeQ0
Shower curtain chip containment
https://youtu.be/ykI_sX42H8A
I love these jaws!!! I can grab the saw cut sides without having to clean them up first.
https://youtu.be/U2n9wmq7GJw
Replacing the rear Y axis bellows
https://youtu.be/Hi-yGh_YYfU
Re: Torus Pro with servos and 4th axis
Modifying a 13" set of rotors
https://youtu.be/ZLlprAAAUAY
Bit of mill turning. I now have a Tormach 15L Slant Pro to do this work on. :)
https://youtu.be/FDupddeBuJ0
Thread milling - testing and final use
https://youtu.be/tOkmPqu8Vl0
https://youtu.be/fdt6nXp5uEk
https://youtu.be/lGoBZnblXkY
"One off" set of brackets I did.
https://youtu.be/oS9iUqjaSVE
https://youtu.be/FxM7Hc3m1XA
https://youtu.be/w_9fH71qNi0
A couple of upper control arms. One is solid, the other is two pieces
https://youtu.be/9okeKNoYEjA
https://youtu.be/9okeKNoYEjA
Ball joint covers for the above arms. I stalled/crashed the spindle in the just after the 1min mark
https://youtu.be/zRDEdBt44vw
Nearly wet myself
https://youtu.be/6u4CaFaiSNg
There's more on my bluehandsvideo youtube channel, so I'll call this enough for now. :)
Re: Torus Pro with servos and 4th axis
I watched the first thread milling video. From my experience I needed to adjust the nominal diameter of the thread mill in my software to get proper fits. Each thread mill is a bit different.
Re: Torus Pro with servos and 4th axis
kvom.....good to know. Thanks! It's the only thread mill I had and that was the first time using it. I'll probably have to go through the entire testing process again when I have to do it again. lol
hhhmmm......the forum won't let me edit any of my posts....need to change one of the vid links.
Re: Torus Pro with servos and 4th axis
I noticed in #214 above that the same vid was linked twice. I guess the forum has a time limit on when you can edit. Not that anyone is watching, but here's the link to the one piece UCA made from a water jet cut blank.
https://youtu.be/cSjm8D8Ggnw
Re: Torus Pro with servos and 4th axis
Interesting that you chamfered the soft jaws. Never needed to do so myself.