Amada Fanuc PEGA 357 no booting

Hi ,
I've got a problem with Amada pega 357 punch turett,
Error e05 s-memory(low) parity error
I phone Amada and say me motherboard was died and 3 other cards for a total of 30000$ .
It's too much for my society.
Can you help me ?


Thanks

Give more info on the control please: photos help.

Hello ,

It's fanuc O4PC

If that help you for find my problem.

The boot screen is freeze with the error E05 , but i can do origin axis .

The machine is connect to old pc win95 on a box named "adr inc"

Thanks

Thanks. Although that control is essentially a Fanuc 0-C control, I am not familiar with the "Error e05 s-memory(low) parity error" that type of an alarm has always been a 'fatal' one: no machine operation could be done until the alarm was cleared.
Do you have a recent backup of the programs, parameters and diagnostics?

I was thinking 10/11/12 or 15A with the connection unit there. Some form of very early MMC or Front end interface hybrid.

Try to replace memory board only & after press+ cancel+ del button or del+rest. Hope you successfully boot O-C controller. My guess have any track is missed in memory board.

Quote:

---

Originally Posted by memoryman

Thanks. Although that control is essentially a Fanuc 0-C control, I am not familiar with the "Error e05 s-memory(low) parity error" that type of an alarm has always been a 'fatal' one: no machine operation could be done until the alarm was cleared.
Do you have a recent backup of the programs, parameters and diagnostics?

---

Hello i've got this program (in attachement), but i 'don't kown if are just maccro or pms parameter and maccro , it's chineese language for me

Today i have deleted memory , RESET + DELETE button at boot , the error is always here

I show you all the cards that Amada wants to sell to try to fix my machine.

How can i replace memory ? i dont 't know where it 'is.

Thanks for help me

The memory chips are soldered and also socketed on the MEM BOARD, (A16B-1212-0210) There are also various other chips on that board involved in the memory area; it's likely that the problem is on that board.
What country and city are you in?

If i remove the memory card (A16B-1212-0210) , i loose all machine parameters ? (PMC) ?
I am in France in "le Mans"

OK, I will see to have the memory card checked,
For the machine parameters, I found some old numbered paper tape, I think it's the parameters but I have no idea how to use the tape reader.

Hello ,

Always with my problem on my Fanuc 04C

I unplug the memorycard , clean and check it , i see nothing.
But when i plug it , i have a new screen error at boot.

I think the eprom slot 3 is died ? it's good ?
Where i can find the microprogram 0156 FC1C if my diagnostic it's correct.

You have lost all volatile data: parameters, programs, diagnostics etc.
Turn the control ON while holding RESET and DELETE buttons;the reload parameters and diagnostics.

Quote:

---

Originally Posted by memoryman

You have lost all volatile data: parameters, programs, diagnostics etc.
Turn the control ON while holding RESET and DELETE buttons;the reload parameters and diagnostics.

---

Already done but I cannot start the machine without the error screen.

Quote:

---

Originally Posted by Neozebulon

Already done but I cannot start the machine without the error screen.

---

Please share the picture of full Masterboad.

Quote:

---

Originally Posted by Neozebulon

Already done but I cannot start the machine without the error screen.

---

Master board error


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by phucrobusl

Please share the picture of full Masterboad.

---

Masterboard

Can you help me, boot (make backup) againt Parameter, PMC, DNC,.. for Pega 244 O4PC.
Thanks so much.

sure