E0 Cn error on Spindle

Hi All, last night my spindle stopped mid job with a E0 Cn error. this is the second time ive had an over current error, last time it was the spindle that was dead, i suspect this one to be dead too as the spare i have on hand works fine.

it is a 220v Huanyang Water Cooled CNC Spindle Milling Motor 220V 2.2KW 24000RPM 400hz spindle GDZ-80-2.2A

my CNC was bought used, it is a greenbull 5x from buildyourcnc, and it came with a Huanyang 110v VFD which outputs 220v. model number HY02D211B-T this was what they supplied, and as i got it used, i didn't get a chance to spec it

The VFD is run off a dedicated 110v 20a supply.

The original spindle lasted from 2015 -Dec 2018 and the one that just died lasted from Dec 2018 to July 2020. It is controlled via 0-10v control from mach4 via a Warp9 ESS


Below are the VFD parameters as they are today, hope i used the correct format. i did some reading and i am really confused what i need is PD008 and PD141 are these both spindle voltages or should one be the VFD voltage.

i understand these spindles are not the best, and that they do die but i want to make sure I've not got settings that are killing them sooner than natural causes.

Any advice would be greatly appreciated.

thanks
Raptor


PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=1 (1 For Remote Control) ( 1 For 0-10v Terminal Control or Remote Trim Pot Control ) ( J1 Also Needs to be set for Terminal Control )

PD002=1

PD003=400 (was 300)

PD004=400

PD005=400

PD006=002.5

PD007=00.50

PD008=110 (Motor Rated Voltage)

PD009=15

PD010=8

PD011=120 ( 100 Minimum Setting with Quality VFD, 120 is Safe for Water Cooled )
(Air cooled 150 depending on Temperature this may be lower )

PD13= 00 ( Is for Factory reset, Only use this to set VFD to Factory Default Settings )

PD014=15 ( Acceleration Adjust to suit)

PD015=15 ( Deceleration Adjust to suit) ( PD15 is ignored IF PD26=1 Then the Spindle will Coast to a Stop)

PD120=000 ( Stall Prevention )

PD141=220 ( Motor Rated Voltage )

PD041=03 ( Carrier Frequency max up to 10 )

PD142=9 (was 7.5)

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM) =3,000= (24,000)

PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD72=400

PD73=000 ( 100 /120 Minimum Setting Water Cooled AIR Cooled 150 )

PD120=000

PD174= 17 (Set to Max VFD Drives Output Amp Rating )

I think im going to go with these settings, any reasons why i shouldn't?

PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=1 (1 For Remote Control) ( 1 For 0-10v Terminal Control or Remote Trim Pot Control ) ( J1 Also Needs to be set for Terminal Control )

PD002=1

PD003=400 (was 300)

PD004=400

PD005=400

PD006=03.0 was 2.5

PD007=1.2 was 0.50

PD008=220 (Motor Rated Voltage) was 110

PD009=15

PD010=8

PD011=120 ( 100 Minimum Setting with Quality VFD, 120 is Safe for Water Cooled )
(Air cooled 150 depending on Temperature this may be lower )

PD13= 00 ( Is for Factory reset, Only use this to set VFD to Factory Default Settings )

PD014=15 ( Acceleration Adjust to suit)

PD015=15 ( Deceleration Adjust to suit) ( PD15 is ignored IF PD26=1 Then the Spindle will Coast to a Stop)

PD120=120 ( Stall Prevention ) was 000

PD141=220 ( Motor Rated Voltage )

PD041=03 ( Carrier Frequency max up to 10 )

PD142=8.5 (was 7.5)

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM) =3,000= (24,000)

PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD72=400

PD73=120 ( 100 /120 Minimum Setting Water Cooled AIR Cooled 150 ) was 000


PD174= 17 (Set to Max VFD Drives Output Amp Rating )

does anyone have any input here?

PD008=220 did not work. it immediately went to the E0 CA error

PD008=110 works