HI SPEED CHECK ERROR WHAT AM I MISSING

Hey everyone,
I posted earlier on a program I'm having problems. Finally i've almost got it. But everyitme I do a hi speed check. Check stops before cut-off on main and g650 on sub. I added a post of the program and noted where the high speed check stops. I'm not getting an error, just stops. Also I'm running a Citizen L20
Thanks

G0X.250
G1Y-.750
G0X.9T0
G50W0.59( OFFSETS)
G0Z.275
/B9
G0X0.9T0
M1

G99G40G18M60(CANCEL MILLING)

(DBR OD TURN)
N5
T0200
G97M3S1=6000
G99
G0X.85T02
G0Z.275
G1G9X.146F.003
G1Z.260
G0X.85T0
M1

!L10 STOPS HERE

( CUT OFF)
N6
T0100
M87
M97
G97M24M3S1=500S2=500
G114.1H1D-2
/B4
(B1)(HIGHPRESSURE ON)
G99G18
G0Z1.15
G650(SUPPORT ON)
!L20
!L30
M3S1=5000
G50W-0.625(LOAD OFFSETS)
G99
/B4
G0X0.850Z0.525T01
G1X-.02F0.0015
/(B1)(HIGHPRESSURE OFF)
G50W0.625(CANCEL OFFSETS)
G97
G113(CANCEL SPIN SYNC)
M86
M96
G600
M5
M25
G4U.5
M8
M8
/M98P8000
M9
M9
M7
G4U.5
G0X-.02Z0.525T0
M6
M56
M53
M118
G999
M118
M5
N999
M2
M99









$2
M118
(SAFE START CODES)
G99
G50Q2000S8000
G50Z0
(END SAFE START CODES)

G610
G600
T3000
G4U.5
G50Z0
M98H7(PROCESS 7 R105.1813.005.1.3)
G50Z0

M98H100(EJECT PART)
!L10

M16(SS OPEN)
M118
G650(SUPPORT ON) STOPS HERE
G0Z-.05
G98G1Z0.26F50.0
G4U.5
!L20
M77(WAIT FOR SYNC)
G99
M15(SS CLOSE)
!L30
G600
G50Z0

G999
M52
M98H7(PROCESS 7 R105.1813.005.1.3)
M98H100(EJECT PART)
M53
N999
M2
M99

N7(PROCESS 7 R105.1813.005.1.3)
T3200
G44G97M24S2=4000
G50U0.102(LOAD TOOL OFFSET)
/B4(HIGH PRESSURE ON)
G99

G0X-.82T32
G0Z-.05
G1Z0.0F.0008
G1X0.0
G0Z-.05

M23S2=4000
G4U1.0
G0X0.12
G0Z-0.05
G1Z0.225F0.0004
G1X0.104
G0Z-0.05

G0X0.141
G1Z0.2215
G1X0.104
G0Z-0.05

G0X0.182
G1Z0.017
G1X0.104
G0Z-0.05

G0X0.804
G0Z0.
G1X0.213
G1X0.202Z0.0055
G1Z0.022
G1X0.169
G3X0.161Z0.026R0.004
G1Z0.225
G1X0.138
G3X0.1352Z0.2256R0.002
G1X0.1212Z0.2326
G3X0.12Z0.234R0.002
G1Z0.368
G1X0.1017

G1Z0.3783
G1X0.12Z0.3692
G1Z0.3667
G1X0.1114Z0.3612
G0Z-0.05
/B4(HIGH PRESSURE OFF)
G50U-0.102(CANCEL TOOL OFFSET)
G97G0Z-.05T0M25
M99

N100(EJECT PART)
M25(SS STOP)
M33
G0Z1.2
G0C0.0
M16(SUB OPEN)
M10(KNOCK-OUT ADVANCE)
G4U1.5
/B4
G4U0.5
/B4
M11(KNOCK-OUT RETURN)
T3000
G50Z0
M119
M99



$0
A
#814=0000008120
#815=0000001000
#816=0000001000
#817=0004000000
#822=0000000020
#824=-000000060
#818=0000012290
#819=0000001000
#820=0000000000
#821=0000002650
#990=0000114000
#991=0000051000
#992=0000061000
#893=0000000000
#25119=0000012290
%
[/RIGHT]

Make sure your c axis isn't runnin out of travel

I wonder about the G0C0.0 in the knock-out routine, do you have C axis control on the sub? Not sure why that is even there. I would take it out. Also I have had a lot of trouble trying to run the program with that M77 in it. it really isn't necessary.

Partmaker is a really good program, but it puts WAY too much crap in the program, I always strip all the junk out before I run a program.

Sounds like since there is no alarm it is looking for the matching wait gode in $2 toolpath. I would check over there.

If you have WIN CNC you can check the Queing commands. not sure but partmaker should check it as well.

Send me your code in .txt format and I will run the queing here for you. Check it. Edit it. and send it back.

The only line I see as strange is;
G97M24M3S1=500S2=500
I would write that line as M3S1=500M24S2=500. Not sure if that is the problem.

DAMP YUOR PROGRAM OUT OF MACHINE, LOAD THIS ONE. YOU WILL FIND ERROR
$1
O5555
(T0202-FRONT-TURN R.015)
(T0303-B-T G.INSERT W.047/R.0025)
(T0100-C/O W.059 R.000)
/M52
M9M6M97M87
M118G113
G50Z-.005
G0X.28Z-.05

M3S1=4000G99

T0200(F/T R.015)
G0X.28Z0T02
G0X.280T0

T0300(B/T G.INSERT W.047/R.0025)
G0X.280T0
M3S1=3000

T0100(C/O W.059)
G0X.28Z.132T01
X.15
G650------------------------------------------------------------
G114.1H1D-2
!L1
G1X-.01F.001
G600----------------------------------------
M3S1=5000
G1X-.05F.015
G113
M8
M8
/M98P8999
M9
M9
M5
M7
G0X-.05Z-.005T0
M56
G999
M5
N999
M2
M99


$2
G99M15
T3000
G50Z0
M98H1
M25
M16
T3000
G50Z0
G650-------------------------------------------
M24S2=3000
M72
G0Z-.05
G98G1Z.03F80.
M77
G4U.2
M15
!L1
M73
G600--------------------------------------------------
M25
G50Z0
G999
M98H1
M53
N999
M2
M99


N1
M72
M33
G0Z1.2M16
M10Z3.4
G4U2.
M11Z3.
M73
T3000
G50Z0
M99
$0
%