Printable View
Battery Backup went dead on machine while sitting. Had all kinds of errors of course when I replaced battery. Got parameters put back in but still have one error code 414 x axis. Does anyone know what line controls this or do I have to look through all the parameter #'s again?
Thanks
Alarm 414, need to check DGN720 to 727 to see which bit is on
You should doubdle check your parameter start from #8100
Ahn Vuong
Thanks for your help! I checked the DGN 720 to 727 on 720 I had a 00100000 but after check my 8100 on I found some wrong changed them and reset it no more code! Now I can't zero return the machine because when I turn the dial it goes from edit - auto - mdi - handle - teach in handle - teach in jog - jog - zero return when I slide the handle on the screen from right to left it says edit, auto, mdi, hndl, hndl, hndl, tjog, jog but it won't show zrn. What is going on? Thanks
You should double check all the Option parameter start from 900
Also need to remember to put all machine timer and keep relay back??
Ahn Vuong
What do you mean by machine timer and relay? Thank you
I am sorry do not know how to explain Timer & Keep relay
When Battery Backup went dead, machine not just lost all parameter, also all your program, timer and keep relay gone too, you may need to contact machine builder to get a copy of the timer and keep relay for your machine
Who is the manufacturer??
Ahn Vuong
Thank you for all your help! Company is YCI supermax rebel 1 machine. I called them for parameter put them all in. I checked the parameters in 900 and when I checked 0901 it was wrong. I tried to enter number but it said "Warning preset #901 #2 this parameter destroy next file in memory from file 1 to 15 now neccessary to clean these files which do you want? del clear these files or cancel? What does this mean? Also I will call them tomorrow to get information.
Thank you
You want to choose the DEL, it is going to delete the program only but you don't have any program anyway
Ahn Vuong
Also request them a Macro program for your machine ATC
Ahn Vuong
Thanks fir all your help! I got the keep and relay settings and put them in. Almost there now it has zer return back but twwo mdi settings instead of one. Now it shake very bad when I home in y axis and gives me error 414 when I try to home in y. They had me reset holding p and cancel while turning on.but didn't help. Thank you in advance!
Holding P and Cancel Key while power up control only when the servo can't find it home position then you do that
"Y Axis shake very bad when you do Zero return and also error 414"
You shoud double check parameter start from #8200
Do you have the origenal parameter from this machine??
Ahn Vuong
They sent me original parameters and also procedure to reset home but it didn't work. Do you have to hold down cancel and p together and where is P? I will check 8400 peremeters
Thankyouu
What do you mean by it didn't work?? are you talking about Zero return doesn't work or servo alarm 414 come up when you try to move the Y Axis?
The "P and Q" key they are locate on the Keypad, normaly is right side of the CRT, you have to press and hold down P, Q and CAN key while power up machine, and wait untill control go to ready position before release P,Q, CAN
Ahn Vuong
I had some numbers wrong in the parameter section, it will zero return now. The only thing now is the mode switch when it goes from mdi to handle it says mdi on screen on both settings is that normal? Thank you for everything again!
I think you still missing a parameter some where, I am sorry I do not know which one to change to fix the problem, you should double check again all the parameter and specialy the #900 to 930
Ahn Vuong
Put program in to test and spindle goes ccw I must have parameter set wrong. Also try to send or receive program but get bad characters on pc screen. Are there parameters for rs232 setting?
Thanks
there are settings to turn on RS232 inputs. turn the handle to MDI i believe, look in settings screen, page down for "input mode" change 0 to 1 or vise versa..
Need to check your baud rate, Parameter 0552 and 0553
If your PC set 4800 then change parameter 0552 & 0553 to 10
If 9600 then parameter set at 11
Ahn Vuong