Jump lines

I'm running sheet parts using subprograms on an VMC-15XT. I use jump lines to restart the program after moving the sheet down and changing the repeat cycle. It works well till the end and I cannot get it to jump to the M30. Can some one tell me what I have missed?

O130(WIL-013 REV2)
(R2)
( T14 | 5/16 DRILL | H14 )
( T11 | 5/16 FLAT ENDMILL | H11 )
( T10 | .285 FORM ENDMILL | H10 )
( T7 | 13/64 END MILL | H7 )
( T8 | 1/2 CENTERDRILL | H8 )
G0G17G40G49G80G90
G28G91X0Y0Z0
#V2=6.75 'X STEP OVER
#V3=4 'SUB REPEAT
#V4=3 'SECOND SUB REPEAT
#R2=V3
#:START2
( 5/16 FLAT ENDMILL TOOL - 11 )
T11M6
G52X0
G0 G90 G54 X-.1993 Y3.114 S7500 M3
G43 H11 Z.5M8
M98P133LR2
G91G28Z0M5
M0(REMOVE SCRAP)
.
.
.
.
#IF R2=V4 THEN GOTO:END "I have tried using the = and EQ, also use part count with no results."
#R2=V4
M0(CHANGE SHEET LOC.)
#GOTO:START2 "I'm happy with this line it changes the part count and re-runs the program"
#:END
M30


Think I'll try the changing my subprograms to subroutines on the next program. It's going to take some getting use to, having them at the start than at the end. I get tired of switching in and out of the editor screen.

Have you tried adding a space GOTO :END

I did finely get the jump lines to work to the #:end_. I still don't know why the first try didn't work, maybe because of the parametric variable R2?

( T8 | 1/2 CENTERDRILL | H8 )
T8M6
G52X0
G0G90G54X-1.3675Y1.9653S7500M3
G43H8Z0.4M8F60.
L401
G52X6.7
L401
G52X13.4
L401
#IFV5=3THENGOTO:END4
G52X20.1
L401
#:END4
M9
G91G28Z0M5
M1
G52X0
G0G90G54Y-11.X19.5
M98P5001
G91G28Z0
G91G28Z0Y0X0M5
#IFV5=3THENGOTO:END "variable V5=0 at this point"
#V5=3 "variable V5=3 is set to 3"
M0(CHANGE SHEET LOC.)
#GOTO:START2 "jumps back and reruns program, when it reaches IF-THEN lines it will GOTO the #:end_"
#:END
#V5=0 "resets variable to 0
T9M6
M2

Quote:

---

Originally Posted by TDC-shop

I did finely get the jump lines to work to the #:end_. I still don't know why the first try didn't work, maybe because of the parametric variable R2?

( T8 | 1/2 CENTERDRILL | H8 )
T8M6
G52X0
G0G90G54X-1.3675Y1.9653S7500M3
G43H8Z0.4M8F60.
L401
G52X6.7
L401
G52X13.4
L401
#IFV5=3THENGOTO:END4
G52X20.1
L401
#:END4
M9
G91G28Z0M5
M1
G52X0
G0G90G54Y-11.X19.5
M98P5001
G91G28Z0
G91G28Z0Y0X0M5
#IFV5=3THENGOTO:END "variable V5=0 at this point"
#V5=3 "variable V5=3 is set to 3"
M0(CHANGE SHEET LOC.)
#GOTO:START2 "jumps back and reruns program, when it reaches IF-THEN lines it will GOTO the #:end_"
#:END
#V5=0 "resets variable to 0
T9M6
M2

---

You are correct. You cannot use "R" as a label. You need to use "L" to designate how many time to repeat sub