Printable View
Hi, have been using your screen set since2010 and it is working perfectly.
I know that my problem isn’t coming from the screen set, Mach doesn’t recognize the federate that I’m asking, no mather if I set to 15 or 1500 it’s always crawling, I can hardly see it move.
When I press the arrows or use my shuttle it moves normally.
Any suggestion of what I should look at to fix it.
Thank you
Is it moving slow when running g-code?
Post the code.
Thank you for the prompt reply, it's only slow while processing the G-Codes, jogging is normal . I was reading your comments on another tread that Kernel frequency on the diagnostics page and see if it's running at 75% speed. (18750 instead of 25000) and make sure FRO is set to 100%, and rapid override too, mine is right on the target.
N10 (##01 ARRONDI 3.5 A 2.5 ##)
N20 (##02 Produced by Rich's Indexer Wizards Version 2.0 ##)
N30 (##03 06/17/2019 1:13:53 AM ##)
N40 (##11 GCode start header code ##)
N50 G20 (Inch units)
N60 G17 (XY plane select)
N70 G90 (Absolute mode)
N80 G40 (Cancel cutter radius compensation)
N90 G49 (Cancel tool length offset)
N100 G80 (Cancel motion mode)
N110 M03 (Spindle on)
N120 (##12 GCode end header code ##)
N130 (##21 Rounding ##)
N140 (##22 ARRONDI 3.5 A 2.5 ##)
N150 (##23 Name = X start, Value = 0, Integer = False, Positive = False, Type = NumEdit ##)
N160 (##23 Name = X end, Value = .5, Integer = False, Positive = False, Type = NumEdit ##)
N170 (##23 Name = Rough diameter, Value = 3.625, Integer = False, Positive = True, Type = NumEdit ##)
N180 (##23 Name = Start diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N190 (##23 Name = End diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N200 (##23 Name = Z depth per pass, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N210 (##23 Name = Rapid diameter, Value = 3.7, Integer = False, Positive = True, Type = NumEdit ##)
N220 (##23 Name = Stepover, Value = .05125, Integer = False, Positive = True, Type = NumEdit ##)
N230 (##23 Name = Feed rate, Value = 150, Integer = False, Positive = True, Type = NumEdit ##)
N240 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N250 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N260 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 0, Integer = True, Positive = True, Type = RadioGroup ##)
N270 G0 Z1.85
N280 G0 A0
N290 G0 X0 Y0
N300 (Z pass 1)
N310 G0 Z1.8125
N320 G1 Z1.7500 F20
N330 G93
N340 G1 A360 F13.6418522650196
N350 G92 A0
N360 G1 X0.5 A3512.1951219512195121951219514 Z1.7500 F1.3982746687639898563027601802
N370 G1 A3872.1951219512195121951219514 F13.6418522650196
N380 G94
N390 G92 A3512.1951219512195121951219514
N400 G0 Z1.85
N410 G0 A3240
N420 G92 A0
N430 G0 X0
N440 (Z pass 2)
N450 G0 Z1.8125
N460 G1 Z1.6875 F20
N470 G93
N480 G1 A360 F14.1471060526129
N490 G92 A0
N500 G1 X0.5 A3512.1951219512195121951219514 Z1.6875 F1.4500614311377068991515178026
N510 G1 A3872.1951219512195121951219514 F14.1471060526129
N520 G94
N530 G92 A3512.1951219512195121951219514
N540 G0 Z1.85
N550 G0 A3240
N560 G92 A0
N570 G0 X0
N580 (Z pass 3)
N590 G0 Z1.8125
N600 G1 Z1.6250 F20
N610 G93
N620 G1 A360 F14.691225516175
N630 G92 A0
N640 G1 X0.5 A3512.1951219512195121951219514 Z1.6250 F1.5058316455114687132266307989
N650 G1 A3872.1951219512195121951219514 F14.691225516175
N660 G94
N670 G92 A3512.1951219512195121951219514
N680 G0 Z1.85
N690 G0 A3240
N700 G92 A0
N710 G0 X0
N720 (Z pass 4)
N730 G0 Z1.8125
N740 G1 Z1.5625 F20
N750 G93
N760 G1 A360 F15.278874536822
N770 G92 A0
N780 G1 X0.5 A3512.1951219512195121951219514 Z1.5625 F1.5660633015035327039672687998
N790 G1 A3872.1951219512195121951219514 F15.278874536822
N800 G94
N810 G92 A3512.1951219512195121951219514
N820 G0 Z1.85
N830 G0 A3240
N840 G92 A0
N850 G0 X0
N860 (Z pass 5)
N870 G0 Z1.8125
N880 G1 Z1.5000 F20
N890 G93
N900 G1 A360 F15.9154943091895
N910 G92 A0
N920 G1 X0.5 A3512.1951219512195121951219514 Z1.5000 F1.6313140482163393719263481673
N930 G1 A3872.1951219512195121951219514 F15.9154943091895
N940 G94
N950 G92 A3512.1951219512195121951219514
N960 G0 Z1.85
N970 G0 A3240
N980 G92 A0
N990 G0 X0
N1000 (Z pass 6)
N1010 G0 Z1.8125
N1020 G1 Z1.4375 F20
N1030 G93
N1040 G1 A360 F16.6074723226326
N1050 G92 A0
N1060 G1 X0.5 A3512.1951219512195121951219514 Z1.4375 F1.7022385100000901090128867227
N1070 G1 A3872.1951219512195121951219514 F16.6074723226326
N1080 G94
N1090 G92 A3512.1951219512195121951219514
N1100 G0 Z1.85
N1110 G0 A3240
N1120 G92 A0
N1130 G0 X0
N1140 (Z pass 7)
N1150 G0 Z1.8125
N1160 G1 Z1.3750 F20
N1170 G93
N1180 G1 A360 F17.3623574282068
N1190 G92 A0
N1200 G1 X0.5 A3512.1951219512195121951219514 Z1.3750 F1.7796103241822267311859206666
N1210 G1 A3872.1951219512195121951219514 F17.3623574282068
N1220 G94
N1230 G92 A3512.1951219512195121951219514
N1240 G0 Z1.85
N1250 G0 A3240
N1260 G92 A0
N1270 G0 X0
N1280 (Z pass 8)
N1290 G0 Z1.8125
N1300 G1 Z1.3125 F20
N1310 G93
N1320 G1 A360 F18.1891363533595
N1330 G92 A0
N1340 G1 X0.5 A3512.1951219512195121951219514 Z1.3125 F1.8643504745410071181004835521
N1350 G1 A3872.1951219512195121951219514 F18.1891363533595
N1360 G94
N1370 G92 A3512.1951219512195121951219514
N1380 G0 Z1.85
N1390 G0 A3240
N1400 G92 A0
N1410 G0 X0
N1420 (Z pass 9)
N1430 G0 Z1.8125
N1440 G1 Z1.2500 F20
N1450 G93
N1460 G1 A360 F19.0985931710274
N1470 G92 A0
N1480 G1 X0.5 A3512.1951219512195121951219514 Z1.2500 F1.9575641237111623009766880575
N1490 G1 A3872.1951219512195121951219514 F19.0985931710274
N1500 G94
N1510 G92 A3512.1951219512195121951219514
N1520 G0 Z1.85
N1530 G0 A3240
N1540 G92 A0
N1550 G0 X0
N1560
N1570
N1580 (##25 Rounding end ##)
N1590 (##21 Rounding ##)
N1600 (##22 ARONDI DEBUT ##)
N1610 (##23 Name = X start, Value = .5, Integer = False, Positive = False, Type = NumEdit ##)
N1620 (##23 Name = X end, Value = .6875, Integer = False, Positive = False, Type = NumEdit ##)
N1630 (##23 Name = Rough diameter, Value = 3.5, Integer = False, Positive = True, Type = NumEdit ##)
N1640 (##23 Name = Start diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N1650 (##23 Name = End diameter, Value = 3.45, Integer = False, Positive = True, Type = NumEdit ##)
N1660 (##23 Name = Z depth per pass, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N1670 (##23 Name = Rapid diameter, Value = 3.6, Integer = False, Positive = True, Type = NumEdit ##)
N1680 (##23 Name = Stepover, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N1690 (##23 Name = Feed rate, Value = 150, Integer = False, Positive = True, Type = NumEdit ##)
N1700 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N1710 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N1720 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 0, Integer = True, Positive = True, Type = RadioGroup ##)
N1730 G0 Z1.8
N1740 G0 A0
N1750 G0 X0.5 Y0
N1760 (Z pass 1)
N1770 G0 Z1.75
N1780 G1 Z1.6875 F20
N1790 G93
N1800 G1 A360 F14.1471060526129
N1810 G92 A0
N1820 G1 X0.6875 A1080 Z1.746875 F4.6340971178220049021885065655
N1830 G1 A1440 F13.6662562941162
N1840 G94
N1850 G92 A1080
N1860 G0 Z1.8
N1870 G0 A1080
N1880 G92 A0
N1890 G0 X0.5
N1900 (Z pass 2)
N1910 G0 Z1.75
N1920 G1 Z1.6250 F20
N1930 G93
N1940 G1 A360 F14.691225516175
N1950 G92 A0
N1960 G1 X0.6875 A1080 Z1.743750 F4.7243686187991871134559182254
N1970 G1 A1440 F13.6907477928512
N1980 G94
N1990 G92 A1080
N2000 G0 Z1.8
N2010 G0 A1080
N2020 G92 A0
N2030 G0 X0.5
N2040 (Z pass 3)
N2050 G0 Z1.75
N2060 G1 Z1.5625 F20
N2070 G93
N2080 G1 A360 F15.278874536822
N2090 G92 A0
N2100 G1 X0.6875 A1080 Z1.740625 F4.8182268754196200359791695912
N2110 G1 A1440 F13.7153272323357
N2120 G94
N2130 G92 A1080
N2140 G0 Z1.8
N2150 G0 A1080
N2160 G92 A0
N2170 G0 X0.5
N2180 (Z pass 4)
N2190 G0 Z1.75
N2200 G1 Z1.5000 F20
N2210 G93
N2220 G1 A360 F15.9154943091895
N2230 G92 A0
N2240 G1 X0.6875 A1080 Z1.737500 F4.9158899852086396706006452113
N2250 G1 A1440 F13.7399950870701
N2260 G94
N2270 G92 A1080
N2280 G0 Z1.8
N2290 G0 A1080
N2300 G92 A0
N2310 G0 X0.5
N2320 (Z pass 5)
N2330 G0 Z1.75
N2340 G1 Z1.4375 F20
N2350 G93
N2360 G1 A360 F16.6074723226326
N2370 G92 A0
N2380 G1 X0.6875 A1080 Z1.734375 F5.0175940934361001796078260334
N2390 G1 A1440 F13.7647518349747
N2400 G94
N2410 G92 A1080
N2420 G0 Z1.8
N2430 G0 A1080
N2440 G92 A0
N2450 G0 X0.5
N2460 (Z pass 6)
N2470 G0 Z1.75
N2480 G1 Z1.3750 F20
N2490 G93
N2500 G1 A360 F17.3623574282068
N2510 G92 A0
N2520 G1 X0.6875 A1080 Z1.731250 F5.1235952993450160478959779022
N2530 G1 A1440 F13.7895979574205
N2540 G94
N2550 G92 A1080
N2560 G0 Z1.8
N2570 G0 A1080
N2580 G92 A0
N2590 G0 X0.5
N2600 (Z pass 7)
N2610 G0 Z1.75
N2620 G1 Z1.3125 F20
N2630 G93
N2640 G1 A360 F18.1891363533595
N2650 G92 A0
N2660 G1 X0.6875 A1080 Z1.728125 F5.2341718091954031650691172477
N2670 G1 A1440 F13.8145339392604
N2680 G94
N2690 G92 A1080
N2700 G0 Z1.8
N2710 G0 A1080
N2720 G92 A0
N2730 G0 X0.5
N2740 (Z pass 8)
N2750 G0 Z1.75
N2760 G1 Z1.2500 F20
N2770 G93
N2780 G1 A360 F19.0985931710274
N2790 G92 A0
N2800 G1 X0.6875 A1080 Z1.725000 F5.34962637422779653791093918
N2810 G1 A1440 F13.8395602688605
N2820 G94
N2830 G92 A1080
N2840 G0 Z1.8
N2850 G0 A1080
N2860 G92 A0
N2870 G0 X0.5
N2880
N2890 (##25 Rounding end ##)
N2900 (##21 Rounding ##)
N2910 (##22 ARRONDI FIN 3.5 A 2.5 ##)
N2920 (##23 Name = X start, Value = 1.3625, Integer = False, Positive = False, Type = NumEdit ##)
N2930 (##23 Name = X end, Value = 1.55, Integer = False, Positive = False, Type = NumEdit ##)
N2940 (##23 Name = Rough diameter, Value = 3.6, Integer = False, Positive = True, Type = NumEdit ##)
N2950 (##23 Name = Start diameter, Value = 3.5, Integer = False, Positive = True, Type = NumEdit ##)
N2960 (##23 Name = End diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N2970 (##23 Name = Z depth per pass, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N2980 (##23 Name = Rapid diameter, Value = 3.67, Integer = False, Positive = True, Type = NumEdit ##)
N2990 (##23 Name = Stepover, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N3000 (##23 Name = Feed rate, Value = 150, Integer = False, Positive = True, Type = NumEdit ##)
N3010 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N3020 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N3030 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 0, Integer = True, Positive = True, Type = RadioGroup ##)
N3040 G0 Z1.835
N3050 G0 A0
N3060 G0 X1.3625 Y0
N3070 (Z pass 1)
N3080 G0 Z1.8
N3090 G1 Z1.7944444444444444444444444444 F20
N3100 G93
N3110 G1 A360 F13.3039735711491
N3120 G92 A0
N3130 G1 X1.55 A1080 Z1.7388888888888888888888888889 F4.5043137838097433741733075909
N3140 G1 A1440 F13.7290206500996
N3150 G94
N3160 G92 A1080
N3170 G0 Z1.835
N3180 G0 A1080
N3190 G92 A0
N3200 G0 X1.3625
N3210 (Z pass 2)
N3220 G0 Z1.8
N3230 G1 Z1.7888888888888888888888888888 F20
N3240 G93
N3250 G1 A360 F13.3452902592583
N3260 G92 A0
N3270 G1 X1.55 A1080 Z1.6777777777777777777777777778 F4.590932376999049654321742421
N3280 G1 A1440 F14.2290843161628
N3290 G94
N3300 G92 A1080
N3310 G0 Z1.835
N3320 G0 A1080
N3330 G92 A0
N3340 G0 X1.3625
N3350 (Z pass 3)
N3360 G0 Z1.8
N3370 G1 Z1.7833333333333333333333333332 F20
N3380 G93
N3390 G1 A360 F13.3868643722155
N3400 G92 A0
N3410 G1 X1.55 A1080 Z1.6166666666666666666666666667 F4.6809476066353089496607458305
N3420 G1 A1440 F14.7669534827532
N3430 G94
N3440 G92 A1080
N3450 G0 Z1.835
N3460 G0 A1080
N3470 G92 A0
N3480 G0 X1.3625
N3490 (Z pass 4)
N3500 G0 Z1.8
N3510 G1 Z1.7777777777777777777777777776 F20
N3520 G93
N3530 G1 A360 F13.4286983233787
N3540 G92 A0
N3550 G1 X1.55 A1080 Z1.5555555555555555555555555556 F4.7745632568030668649601037712
N3560 G1 A1440 F15.347083798147
N3570 G94
N3580 G92 A1080
N3590 G0 Z1.835
N3600 G0 A1080
N3610 G92 A0
N3620 G0 X1.3625
N3630 (Z pass 5)
N3640 G0 Z1.8
N3650 G1 Z1.7722222222222222222222222220 F20
N3660 G93
N3670 G1 A360 F13.4707945563673
N3680 G92 A0
N3690 G1 X1.55 A1080 Z1.4944444444444444444444444445 F4.8719997455392321693925358784
N3700 G1 A1440 F15.9746597155434
N3710 G94
N3720 G92 A1080
N3730 G0 Z1.835
N3740 G0 A1080
N3750 G92 A0
N3760 G0 X1.3625
N3770 (Z pass 6)
N3780 G0 Z1.8
N3790 G1 Z1.7666666666666666666666666664 F20
N3800 G93
N3810 G1 A360 F13.5131555455383
N3820 G92 A0
N3830 G1 X1.55 A1080 Z1.4333333333333333333333333334 F4.9734958573452577140918909623
N3840 G1 A1440 F16.6557498584542
N3850 G94
N3860 G92 A1080
N3870 G0 Z1.835
N3880 G0 A1080
N3890 G92 A0
N3900 G0 X1.3625
N3910 (Z pass 7)
N3920 G0 Z1.8
N3930 G1 Z1.7611111111111111111111111108 F20
N3940 G93
N3950 G1 A360 F13.5557837964706
N3960 G92 A0
N3970 G1 X1.55 A1080 Z1.3722222222222222222222222223 F5.0793106968415379169364385754
N3980 G1 A1440 F17.3975039007335
N3990 G94
N4000 G92 A1080
N4010 G0 Z1.835
N4020 G0 A1080
N4030 G92 A0
N4040 G0 X1.3625
N4050 (Z pass 8)
N4060 G0 Z1.8
N4070 G1 Z1.7555555555555555555555555552 F20
N4080 G93
N4090 G1 A360 F13.5986818464594
N4100 G92 A0
N4110 G1 X1.55 A1080 Z1.3111111111111111111111111112 F5.1897258972115588706396633341
N4120 G1 A1440 F18.2084045062762
N4130 G94
N4140 G92 A1080
N4150 G0 Z1.835
N4160 G0 A1080
N4170 G92 A0
N4180 G0 X1.3625
N4190 (Z pass 9)
N4200 G0 Z1.8
N4210 G1 Z1.7499999999999999999999999996 F20
N4220 G93
N4230 G1 A360 F13.6418522650196
N4240 G92 A0
N4250 G1 X1.55 A1080 Z1.2500000000000000000000000001 F5.3050481230619134762282443135
N4260 G1 A1440 F19.0985931710274
N4270 G94
N4280 G92 A1080
N4290 G0 Z1.835
N4300 G0 A1080
N4310 G92 A0
N4320 G0 X1.3625
N4330
N4340 (##25 Rounding end ##)
N4350 (##21 Rounding ##)
N4360 (##22 DIAM 2.5 ##)
N4370 (##23 Name = X start, Value = 1.55, Integer = False, Positive = False, Type = NumEdit ##)
N4380 (##23 Name = X end, Value = 3.25, Integer = False, Positive = False, Type = NumEdit ##)
N4390 (##23 Name = Rough diameter, Value = 3.55, Integer = False, Positive = True, Type = NumEdit ##)
N4400 (##23 Name = Start diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N4410 (##23 Name = End diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N4420 (##23 Name = Z depth per pass, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N4430 (##23 Name = Rapid diameter, Value = 3.6, Integer = False, Positive = True, Type = NumEdit ##)
N4440 (##23 Name = Stepover, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N4450 (##23 Name = Feed rate, Value = 150, Integer = False, Positive = True, Type = NumEdit ##)
N4460 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N4470 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N4480 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 0, Integer = True, Positive = True, Type = RadioGroup ##)
N4490 G0 Z1.8
N4500 G0 A0
N4510 G0 X1.55 Y0
N4520 (Z pass 1)
N4530 G0 Z1.775
N4540 G1 Z1.7166666666666666666666666667 F20
N4550 G93
N4560 G1 A360 F13.9067426002627
N4570 G92 A0
N4580 G1 X3.25 A9792.0 Z1.7166666666666666666666666667 F0.5112687183850391787840988989
N4590 G1 A10152.0 F13.9067426002627
N4600 G94
N4610 G92 A9792.0
N4620 G0 Z1.8
N4630 G0 A9720
N4640 G92 A0
N4650 G0 X1.55
N4660 (Z pass 2)
N4670 G0 Z1.775
N4680 G1 Z1.6583333333333333333333333334 F20
N4690 G93
N4700 G1 A360 F14.3959245007745
N4710 G92 A0
N4720 G1 X3.25 A9792.0 Z1.6583333333333333333333333334 F0.5292524091094659860638227825
N4730 G1 A10152.0 F14.3959245007745
N4740 G94
N4750 G92 A9792.0
N4760 G0 Z1.8
N4770 G0 A9720
N4780 G92 A0
N4790 G0 X1.55
N4800 (Z pass 3)
N4810 G0 Z1.775
N4820 G1 Z1.6000000000000000000000000001 F20
N4830 G93
N4840 G1 A360 F14.9207759148652
N4850 G92 A0
N4860 G1 X3.25 A9792.0 Z1.6000000000000000000000000001 F0.5485473372071975152483908252
N4870 G1 A10152.0 F14.9207759148652
N4880 G94
N4890 G92 A9792.0
N4900 G0 Z1.8
N4910 G0 A9720
N4920 G92 A0
N4930 G0 X1.55
N4940 (Z pass 4)
N4950 G0 Z1.775
N4960 G1 Z1.5416666666666666666666666668 F20
N4970 G93
N4980 G1 A360 F15.4853458143466
N4990 G92 A0
N5000 G1 X3.25 A9792.0 Z1.5416666666666666666666666668 F0.5693023340936252857478704911
N5010 G1 A10152.0 F15.4853458143466
N5020 G94
N5030 G92 A9792.0
N5040 G0 Z1.8
N5050 G0 A9720
N5060 G92 A0
N5070 G0 X1.55
N5080 (Z pass 5)
N5090 G0 Z1.775
N5100 G1 Z1.4833333333333333333333333335 F20
N5110 G93
N5120 G1 A360 F16.0943200879445
N5130 G92 A0
N5140 G1 X3.25 A9792.0 Z1.4833333333333333333333333335 F0.5916896404208541044278754969
N5150 G1 A10152.0 F16.0943200879445
N5160 G94
N5170 G92 A9792.0
N5180 G0 Z1.8
N5190 G0 A9720
N5200 G92 A0
N5210 G0 X1.55
N5220 (Z pass 6)
N5230 G0 Z1.775
N5240 G1 Z1.4250000000000000000000000002 F20
N5250 G93
N5260 G1 A360 F16.75315190441
N5270 G92 A0
N5280 G1 X3.25 A9792.0 Z1.4250000000000000000000000002 F0.6159096968039691376340716201
N5290 G1 A10152.0 F16.75315190441
N5300 G94
N5310 G92 A9792.0
N5320 G0 Z1.8
N5330 G0 A9720
N5340 G92 A0
N5350 G0 X1.55
N5360 (Z pass 7)
N5370 G0 Z1.775
N5380 G1 Z1.3666666666666666666666666669 F20
N5390 G93
N5400 G1 A360 F17.4682254613056
N5410 G92 A0
N5420 G1 X3.25 A9792.0 Z1.3666666666666666666666666669 F0.6421971612377911379527796282
N5430 G1 A10152.0 F17.4682254613056
N5440 G94
N5450 G92 A9792.0
N5460 G0 Z1.8
N5470 G0 A9720
N5480 G92 A0
N5490 G0 X1.55
N5500 (Z pass 8)
N5510 G0 Z1.775
N5520 G1 Z1.3083333333333333333333333336 F20
N5530 G93
N5540 G1 A360 F18.2470635391982
N5550 G92 A0
N5560 G1 X3.25 A9792.0 Z1.3083333333333333333333333336 F0.6708285359793758492218072936
N5570 G1 A10152.0 F18.2470635391982
N5580 G94
N5590 G92 A9792.0
N5600 G0 Z1.8
N5610 G0 A9720
N5620 G92 A0
N5630 G0 X1.55
N5640 (Z pass 9)
N5650 G0 Z1.775
N5660 G1 Z1.2500000000000000000000000003 F20
N5670 G93
N5680 G1 A360 F19.0985931710274
N5690 G92 A0
N5700 G1 X3.25 A9792.0 Z1.2500000000000000000000000003 F0.7021319295395563056151942624
N5710 G1 A10152.0 F19.0985931710274
N5720 G94
N5730 G92 A9792.0
N5740 G0 Z1.8
N5750 G0 A9720
N5760 G92 A0
N5770 G0 X1.55
N5780
N5790
N5800 (##25 Rounding end ##)
N5810 (##21 Rounding ##)
N5820 (##22 TAPER ##)
N5830 (##23 Name = X start, Value = 1.55, Integer = False, Positive = False, Type = NumEdit ##)
N5840 (##23 Name = X end, Value = 3.25, Integer = False, Positive = False, Type = NumEdit ##)
N5850 (##23 Name = Rough diameter, Value = 2.55, Integer = False, Positive = True, Type = NumEdit ##)
N5860 (##23 Name = Start diameter, Value = 2.5, Integer = False, Positive = True, Type = NumEdit ##)
N5870 (##23 Name = End diameter, Value = 1.875, Integer = False, Positive = True, Type = NumEdit ##)
N5880 (##23 Name = Z depth per pass, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N5890 (##23 Name = Rapid diameter, Value = 2.6, Integer = False, Positive = True, Type = NumEdit ##)
N5900 (##23 Name = Stepover, Value = .0625, Integer = False, Positive = True, Type = NumEdit ##)
N5910 (##23 Name = Feed rate, Value = 150, Integer = False, Positive = True, Type = NumEdit ##)
N5920 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N5930 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N5940 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 0, Integer = True, Positive = True, Type = RadioGroup ##)
N5950 G0 Z1.3
N5960 G0 A0
N5970 G0 X1.55 Y0
N5980 (Z pass 1)
N5990 G0 Z1.275
N6000 G1 Z1.2708333333333333333333333333 F20
N6010 G93
N6020 G1 A360 F18.7855014796991
N6030 G92 A0
N6040 G1 X3.25 A9792.0 Z1.21875 F0.7050695328446624361749580071
N6050 G1 A10152.0 F19.5883006882333
N6060 G94
N6070 G92 A9792.0
N6080 G0 Z1.3
N6090 G0 A9720
N6100 G92 A0
N6110 G0 X1.55
N6120 (Z pass 2)
N6130 G0 Z1.275
N6140 G1 Z1.2666666666666666666666666666 F20
N6150 G93
N6160 G1 A360 F18.8472958924613
N6170 G92 A0
N6180 G1 X3.25 A9792.0 Z1.16250 F0.7226044056979415988859959194
N6190 G1 A10152.0 F20.5361216892768
N6200 G94
N6210 G92 A9792.0
N6220 G0 Z1.3
N6230 G0 A9720
N6240 G92 A0
N6250 G0 X1.55
N6260 (Z pass 3)
N6270 G0 Z1.275
N6280 G1 Z1.2624999999999999999999999999 F20
N6290 G93
N6300 G1 A360 F18.9094981891361
N6310 G92 A0
N6320 G1 X3.25 A9792.0 Z1.10625 F0.7410336652337808200651195209
N6330 G1 A10152.0 F21.5803312666977
N6340 G94
N6350 G92 A9792.0
N6360 G0 Z1.3
N6370 G0 A9720
N6380 G92 A0
N6390 G0 X1.55
N6400 (Z pass 4)
N6410 G0 Z1.275
N6420 G1 Z1.2583333333333333333333333332 F20
N6430 G93
N6440 G1 A360 F18.9721124215504
N6450 G92 A0
N6460 G1 X3.25 A9792.0 Z1.05000 F0.760427528519324362014284631
N6470 G1 A10152.0 F22.7364204416993
N6480 G94
N6490 G92 A9792.0
N6500 G0 Z1.3
N6510 G0 A9720
N6520 G92 A0
N6530 G0 X1.55
N6540 (Z pass 5)
N6550 G0 Z1.275
N6560 G1 Z1.2541666666666666666666666665 F20
N6570 G93
N6580 G1 A360 F19.0351426953762
N6590 G92 A0
N6600 G1 X3.25 A9792.0 Z0.99375 F0.7808637600399683785871671938
N6610 G1 A10152.0 F24.0233876365125
N6620 G94
N6630 G92 A9792.0
N6640 G0 Z1.3
N6650 G0 A9720
N6660 G92 A0
N6670 G0 X1.55
N6680 (Z pass 6)
N6690 G0 Z1.275
N6700 G1 Z1.2499999999999999999999999998 F20
N6710 G93
N6720 G1 A360 F19.0985931710274
N6730 G92 A0
N6740 G1 X3.25 A9792.0 Z0.93750 F0.8024287137194875361775964933
N6750 G1 A10152.0 F25.4647908947033
N6760 G94
N6770 G92 A9792.0
N6780 G0 Z1.3
N6790 G0 A9720
N6800 G92 A0
N6810 G0 X1.55
N6820
N6830 (##25 Rounding end ##)
N6840 (##31 GCode start footer code ##)
N6850 M05 (Spindle off)
N6860 M30 (Program end and rewind)
N6870 (##32 GCode end footer code ##)
N6880 (##04 End file ##)
That code uses G93 Inverse time feedrates.
Have you run any code from that Wizard that runs correctly?
The wizard says it ONLY works with Mach3 3.042.029. Is that the version you are using?
My Mach3 version is 3.042-040 and yes I have already run codes correctly with this software.
Thank you
I generated a square Gcode with vcarve, cutting air and the feedrate is ok
Sorry, but I really don't know what else to look for.
Does all code run slow now? Or just this one?
Does all code run slow now? Or just this one?
I don't know because when I saw it going this slow I stop the process (speed is like comparing a turtle and a rabbit)
Is the feedrate set in the Wizard? If so, try increasing it.
Yes, even if I set to 15 or 1500 it’s always crawling
Looking at the program,
N1770 G0 Z1.75
N1780 G1 Z1.6875 F20
N1790 G93
N1800 G1 A360 F14.1471060526129
N1810 G92 A0
I see a Z movement on line 1780 - does that line run fine?
If not, at a decimal point to the feedrate and see if that helps.
If 1780 runs fine, and line 1800 runs slow, I would suspect it will take 14.147 minutes to complete. Can you time that to verify?
Chris D
No, it should take 1/14.147 minutes, or 4.2 seconds.
It's inverse time mode.
Can I delete the code G93 wherever I see it
I found the Code of another post that I made in 2015, load it up on Mach and run perfectly, took about 3 minutes can you check it to seen if you find something different. Thank you
N10 (##01 RÉMI OLIVIER ##)
N20 (##02 Produced by Rich's Indexer Wizards Version 2.0 ##)
N30 (##03 07/25/2015 1:26:53 AM ##)
N40 (##11 GCode start header code ##)
N50 G20 (Inch units)
N60 G17 (XY plane select)
N70 G90 (Absolute mode)
N80 G40 (Cancel cutter radius compensation)
N90 G49 (Cancel tool length offset)
N100 G80 (Cancel motion mode)
N110 M03 (Spindle on)
N120 (##12 GCode end header code ##)
N130 (##21 Rounding ##)
N140 (##22 DATE: 24-07-2015 ##)
N150 (##23 Name = X start, Value = .625, Integer = False, Positive = False, Type = NumEdit ##)
N160 (##23 Name = X end, Value = 14.5, Integer = False, Positive = False, Type = NumEdit ##)
N170 (##23 Name = Rough diameter, Value = 3.54, Integer = False, Positive = True, Type = NumEdit ##)
N180 (##23 Name = Start diameter, Value = 2.53, Integer = False, Positive = True, Type = NumEdit ##)
N190 (##23 Name = End diameter, Value = 2.53, Integer = False, Positive = True, Type = NumEdit ##)
N200 (##23 Name = Z depth per pass, Value = .125, Integer = False, Positive = True, Type = NumEdit ##)
N210 (##23 Name = Rapid diameter, Value = 4, Integer = False, Positive = True, Type = NumEdit ##)
N220 (##23 Name = Stepover, Value = .5, Integer = False, Positive = True, Type = NumEdit ##)
N230 (##23 Name = Feed rate, Value = 60, Integer = False, Positive = True, Type = NumEdit ##)
N240 (##23 Name = Plunge rate, Value = 20, Integer = False, Positive = True, Type = NumEdit ##)
N250 (##23 Name = Rotary axis rotation;CW;CCW, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N260 (##23 Name = Cut direction;Bidirectional;Unidirectional, Value = 1, Integer = True, Positive = True, Type = RadioGroup ##)
N270 G0 Z2
N280 G0 A0
N290 G0 X0.625 Y0
N300 (Z pass 1)
N310 G0 Z1.77
N320 G1 Z1.669 F20
N330 G93
N340 G1 A360 F5.7215677564492
N350 G92 A0
N360 G1 X14.5 A9990.00 Z1.669 F0.2059486573617461315405719131
N370 G1 A10350.00 F5.7215677564492
N380 G94
N390 G92 A9990.00
N400 (Z pass 2)
N410 G1 Z1.568 F20
N420 G93
N430 G1 A10350.00 F6.09011261831232
N440 G92 A9990.00
N450 G1 X0.625 A0 Z1.568 F0.2191814311232264617611854266
N460 G1 A360 F6.09011261831232
N470 G94
N480 G92 A0
N490 (Z pass 3)
N500 G1 Z1.467 F20
N510 G93
N520 G1 A360 F6.50940462543539
N530 G92 A0
N540 G1 X14.5 A9990.00 Z1.467 F0.2342287808614696468213212861
N550 G1 A10350.00 F6.50940462543539
N560 G94
N570 G92 A9990.00
N580 (Z pass 4)
N590 G1 Z1.366 F20
N600 G93
N610 G1 A10350.00 F6.99070028222088
N620 G92 A9990.00
N630 G1 X0.625 A0 Z1.366 F0.2514907413468632880699965455
N640 G1 A360 F6.99070028222088
N650 G94
N660 G92 A0
N670 (Z pass 5)
N680 G1 Z1.265 F20
N690 G93
N700 G1 A360 F7.54885105574207
N710 G92 A0
N720 G1 X14.5 A9990.00 Z1.265 F0.2714940071627127727680585424
N730 G1 A10350.00 F7.54885105574207
N740 G94
N750 G92 A9990.00
N760 G0 Z2
N770 G0 A9720
N780 G92 A0
N790 G0 X0.625
N800
N810 (##25 Rounding end ##)
N820 (##31 GCode start footer code ##)
N830 M05 (Spindle off)
N840 M30 (Program end and rewind)
N850 (##32 GCode end footer code ##)
N860 (##04 End file ##)
What's the velocity setting for your A axis?
18036 and have a gearbox with a 10/1 ratio, did you see my last post
Both programs appear to run fine in demo mode.
Changing the feedrate does indeed change the speed.
Note that in G93 mode, the feedrates are specified in time, not actual feedrate.
In G93 mode, a feedrate of 20 means it should take 1.2 seconds to complete the move. If the machine can't complete the move that fast, it won't go any faster. G93 feedrates much higher than that will not likely go any faster.
The only thing I can suggest is to hand code some simple G93 moves, and see if it's working like it should be.
The good news of the day, my problem is solve: Trying to get a smooth finish = (less sanding), in the wizard I was setting the stepover with a two small value .0625.
Change it to .25 and now the gantry is moving, It’ not a rocket but it suit my needs.
I want to thank you ever so much for trying to help me out