-
Hi guys i had the very same trouble with my interact 1 with 2500 control the same message came up with spindel drive fault.We tracked it down to the small transformer on the mti board it did get fried ,if you look closely you can see the resin all burnt.I did some very long hours searching around for imformation on the transformer and after finding out the neccessary values,i had a much more heavy duty one made, and fitted it away from the board, on the inside of the cabinet on a insulated pad.And thank goodness she s been running well since.
-
Hi machintek , I am new to the site so please excuse. I need info on KTK spindle drive fitted to a Bridgeport 4 Interact. The only real info I can give is it has an MT1-1 board which seems ok. I am not outputing a start signal to the TNC-155 from terminal 29 and i believe the problem is on the main drive board. Any drawings or info greatly appreciated , thanks , Alexander...
-
Alexander, i need a email address to send it to.
George
-
Hi George , Re KTK drive , my email is [email protected] , thanks for the prompt reply , kind regards , Alexander...
-
KTK DRIVE
Hi George , thanks for your help. The info you provided got the drive repaired , much obliged , Alexander....
-
George,
First thanks for all your help in the forum.
You have mentioned a set of KTK service notes about 6mb in size. I have the KTK drive that is running right now, but would like to be prepared when the time comes. Could you please send me the service notes?
My e-mail is [email protected]
Thanks,
Paul
P.S. I might be able to reduce the file size with some PDF tools that I have, would you be interested in a reduced file size version?
-
Can anyone send me those notes for the KTK drive also? Mine keeps blowing capcitors. I thought it was a thyristor problem, but even with that replaced more smelly smoke... Thanks. My email is clubpasser_at_gmail.com
Brian
-
Hi George , after about 50 running hours the spindle failed , it just keep rotating but it does not obey to the up and down manual stick , I just turn off the machined I tried to make the home process , and it does not make home because Z axis is not possible to move , The MT1 board has it´s red led on , and their 2 fuses are ok , could any body tell me how could I trouble shoot this failure ?
Thanks
Alejandro
-
If the Z axis does not move I would expect some alarm to come up.
The Z homes homes first. Are the drives enabling (turning on)?
Axis drive fault? Gross positioning error? Fuse? Overload?
George
-
Hi guys.
Anyone of you still have that maintenance dokumentation for this
KTK interface board and MT 1-1.
I did happend to get an almost unused BP interact 2 Mk 2 from the school here. And i know that machine well cause my dad was the theacher in the class for cnc. It doesnt have a lot of hrs in use and looks as new still, so i think its to bad to scrap it.
The problem is that if trying to start spindle it says spindle drive fault.
And i heard the MT 1-1 board humming/buzz.
An electrician did check the boards but he was not able to find the problem, but i think if having the needed information its easier.
So if anyone got it i be pleased if you coul e mail me an copy.
Geir Ove
([email protected])
-
Spindle Drive Wont work!
Hi all -
I'm new.. I have a Bridgeport Interact 1 MK2.
The MTI-1 board blew up.. replaced the Varistor, Caps, Resistors and some diodes.. Light come on, on the PCB, but the Spindle motor wont switch on.. No errors given, program just hangs waiting for motor to start...
I see here the transformer on MTI-1 pbc could be blown?
I will also check the outputs from TNC Unit, but if anyone still has this info pack that would be amazing.. my email is [email protected]
I see some people have had motor problems, but the motor wasnt running when my MTI-1 board blew up, I i susspect there is a fault else where?
Many thanks for any advice :)
Dan
**update.. Since then I have also found 2 Diodes blown up in the supply cab.. Replaced both of those..
I injected 24v @ 5ma on 22 MT1 board and the spinndle motor run, removed volts and it stopped
My Problem is currently. Once the controller has done its memory test it is not reporting Y- Axis over mark... The Orange Motor Drive on Switch/Light will not stay on Now
-
Is the red led on the MTI board lit. If not i think its the MTI board who is faulty.
I had mine fixed now, and the above was my problem.
I had it fixed at Machine Support Services
I did mail them and talked whit Mike Colton [[email protected]]
Sendt him the board and had it fixed at a reasonable price.
It came back tested and ready to plug and forget.
I guess he also is able to help whit servos and problems of indexing the machine. just mail or call to ask.