Can you share me " UNSPLIT eeprom 6m"???
My mail: [email protected]
Printable View
Can you share me " UNSPLIT eeprom 6m"???
My mail: [email protected]
So I need a good guy with a Fanuc PC writer to help me if y want to modify my ladder ?
I know right we do not able to edit a ladder if we read it form other eprom programmer.
We need to use a Fanuc pc writer with a old dos computer (because a serial port needed and dos fladder programme) but i don't have a Fanuc pc writer.
I have already my OE1.bin And OE2.Bin files reddy to go and I want to activate drip feed G127.5 on my ladder,
Please someone can help me? My e-mail [email protected], Thanks !!
Hello Friends.
I appreciate if someone that has the necessary equipment, can merge the attached eprom images and send the EX file to this mail : [email protected]
thanks in advance.
Hi friends,
I am wondering if anyone can help me with the BIN data file of EPROM PMC 0E1 as below.
The machine is : CNC Lathe, Taitung TL-15S, Fanuc 0-TC
Unfortunately, the ROM was damaged and I need the data file for replacement. Thanks a lot for all help
Hello !
I think you need to find someone with the seam machine and have a copy of are ladder. Also the ladder is very specific to the machine so if you find it, it can be not york perfectly...
Have you tried to copy your EPROMs to a new one with a eprom programmer ?
Sorry for my English , I talk French :)
Thanks a lot for your quick response! I well understood your recommendation :)
Yes, I also think the best is looking for the same machine, then copy the BIN file data into a new EPROM by Programmer. But unfortunately again, there is only that machine I've known until now, no other same machine I could find in the country. This is very specific machine type, the MTB Taitung no more handles this machine. I hope it exists somewhere in other countries that will help me with this case
Also, I have tried to copy data by EPROM Programmer to a new ROM already, but because the data is damaged, the new ROM made the same errors as the old one which is identical data copied.
The ROM is confirmed problem, as when I tested with other ROMs from a different machine, the machine could boot completely without error 998, but of course, it cannot run because the program inside different.
I hope to be lucky if someone has this data and will help me, then the problem will be solved perfectly
Ok, i think yo have to make a new post for it with alle information about your contrôler and machine. you can try to communicate with the machine bulder sometime it can work..., also, i dont know but if you can load it on fanuc ladder III,. It can be repaired ?!?
Sorry, I have not yet worked with Fanuc Ladder Programmer, as I heard it should have some tools which are necessary for editing. Do you know what tools and how to combine/convert 2 .BIN files 0E1 and 0E2 to a Fanuc Ladder file for editing or repairing any errors, then reconvert it to 2 BIN files for loading to EPROM? Fanuc Ladder III application can be used for that purpose? Where we can get that software? Thanks again.
It's depend of witch version of controler you have, if it's a 0M-C it can be easier than if you have a 0M-B,
The controller of machine I mentioned is 0-TC. So if I have 2 .BIN files of 0E1 and 0E2, I wondering if someone can help to convert them to a Ladder file so that can be eddied.
What Fanuc Ladder software can be used to edit this Ladder file? Thanks
I think for the c version you can use fanuc in ladder III,
send me OE1 & OE2 FILES on [email protected] i will convert a files for you.
Is this the case also with fapt ladder for dos, runing on a standard pc with serial port?
I try to download a ladder i wrote for my machine/compile with a fapt ladder on a standard pc with serial port but when i press F6->F3 i got a red message on the pc screen
"Port initialize error serial port communication is impossible"
The pc which the fapt ladder is running was able to receive the parameters i send from the OM-F controller, so the cable->serial port is ok.
The cable is just a three wire connection, do i have to use the 5 wire cabling, with handshake, or this is not importand?
Any help will be appreciated.
Is this the case also with fapt ladder for dos, runing on a standard pc with serial port?
I try to download a ladder i wrote for my machine/compile with a fapt ladder on a standard pc with serial port but when i press F6->F3 i got a red message on the pc screen
"Port initialize error serial port communication is impossible"
The pc which the fapt ladder is running was able to receive the parameters i send from the OM-F controller, so the cable->serial port is ok.
The cable is just a three wire connection, do i have to use the 5 wire cabling, with handshake, or this is not importand?
Any help will be appreciated.
Attachment 461814
Try powering off the PC and don't start any other communicating between the machine and laptop. If I start my PC without anything connected to the serial port I still don’t get that alarm. Sounds like the serial port is tied up with whatever you did last with it. Or you have a blown port. Did you try to go both ways with communicating?
It's a standard ibm compatible pc running pure msdos 6.22, nothing else.The serial port is checked, because i could receive the parameters send from CNC.
You can receive the parameters but can you send? Fladder needs to see it go bothways.
Ok i did not check that. I will do it on Monday and lets you know. Thanks for the tip.
I finaly managed to send the PMC programm via serial. The problem was that the ms-dos directory was not shared and for some reason i don't know the fladder gould not initialize the com port.When i include to the autoexec.bat the command PATH=C;\MSDOS;C\FLADDER it worked. So i was finaly able to send the *.#ex file to the OM-F.:wee:
GEAST1967
TWO TO ALL
COULD YOU HELP ME WITH THE STEPS YOU FOLLOWED TO REACH YOUR SUCCESS
I WANT TO DO THE SAME ON MY LATHE THANK YOU AND I HAVE THE FAPT LADDER II SOFTWARE ON WINDOWS 98
THANK YOU
Yes i can help you, but what i did was with Ladder I.