4 Attachment(s)
I need a manual for VFD ZONCN NZ200
Hello everyone.
I need a manual for VFD ZONCN NZ200.
I wrote to the supplier. I wrote to the manufacturer and no one answered me.
Can you help me please?
Thanks Jirka
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
jirkamm
Hello everyone.
I need a manual for VFD ZONCN NZ200.
I wrote to the supplier. I wrote to the manufacturer and no one answered me.
Can you help me please?
Thanks Jirka
What is the manufactures name
Re: I need a manual for VFD ZONCN NZ200
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
jirkamm
ZONCN
Thanks
What do you need to know about it I don't have the manual but may be able to help
Re: I need a manual for VFD ZONCN NZ200
Hello.
I need to set - "device error" for relay output 1.
Set to relay output 2 - "device on" output
For analog output I need to set - output "Current frequency" - 0-10V.
But it probably doesn't have an analog VDF output.
Thank you
Re: I need a manual for VFD ZONCN NZ200
Next, I need to set to control the pump power with an external potentiometer.
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
jirkamm
Next, I need to set to control the pump power with an external potentiometer.
I need a clear photo of the low voltage terminals
And no you would not use any of the relay output for a Pot
Tell me what your VFD is being used for and what it is driving
1 Attachment(s)
Re: I need a manual for VFD ZONCN NZ200
Hi.
"And no you would not use any of the relay output for a Pot" (I don't understand this sentence)
VFD is used to control the vacuum pump power for the vacuum table. I need to adjust the power with a potentiometer. When milling holes and grooves I need to increase performance. I meant to connect the potentiometer and pressure sensor in series.
Thanks
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
jirkamm
Hi.
"And no you would not use any of the relay output for a Pot" (I don't understand this sentence)
VFD is used to control the vacuum pump power for the vacuum table. I need to adjust the power with a potentiometer. When milling holes and grooves I need to increase performance. I meant to connect the potentiometer and pressure sensor in series.
Thanks
Not a very good photo the +10 AVI and Ground Terminals are what your Pot connects to AVI to the center Pot connection there is also a Jumper or switch that needs to be set J2 to AVI it is beside the terminal block
There may be a Parameter to set also
1 Attachment(s)
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
CNCINDUSTRY
Hi, I have one, how to send it to you?
You can attach it here, open a post, go to Advanced scroll down and attach a PDF File
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
CNCINDUSTRY
Awful,size limited.
Do you need the wiring diagrams? Maybe later.
Please send it to [email protected]. Max. 20Mb.
Thanks
Jirka
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
CNCINDUSTRY
Do you need to controll the VFD dynamically?Then you need a controller which has analog input and output module. Such as PLC.
The potentiometer and pressure sensor connect to the controller's input terminals, and its output terminal connect to the VFD‘s analog input terminals.
Yes. I need to dynamically. I told the supplier that I needed it this way. The supplier said - ok.
I see that I can throw away the VFD.
Thanks
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
jirkamm
Yes. I need to dynamically. I told the supplier that I needed it this way. The supplier said - ok.
I see that I can throw away the VFD.
Thanks
Your VFD is not different from any other, I'm sure you could do what is needed if you get creative, your sensor would be controlled from your machine control and would output a voltage change to adjust the VFD Drives motor RPM as needed not hard to do at all
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
mactec54
Your VFD is not different from any other, I'm sure you could do what is needed if you get creative, your sensor would be controlled from your machine control and would output a voltage change to adjust the VFD Drives motor RPM as needed not hard to do at all
It is true. I will have linuxcnc and Beckhoff EL3064 and EL4004 there. That could work.
Good idea.
Thanks
Re: I need a manual for VFD ZONCN NZ200
Quote:
Originally Posted by
CNCINDUSTRY
Hi, I have one, how to send it to you?
HiGood Day! I need the manual also, would it be possible for you to share it to me?