Spindle drive fault

I have a mid 80's Hurco BMC-30, with a Fanuc Drive. I have an error: Spindle Drive Fault Check Drive System. When this happens there is an AL 02 code on the drive. I have a real nice Hurco repairman who knows that I can do most of these repairs myself I am just not very good at diagnosing the problem yet. He hooked me up with a guy from a place called Precision Zone inc, in Wheeling, IL. who said my drive was bad. I ordered one from him and replaced it. That was not the issue, it does the same thing. He mentioned something about the encoder being bad and he took the drive back. My questions are: Does anyone know where the encoder might be located I can't find it listed anywhere in the manual and maybe a good place to get one? If it is located in the motor itself should I just replace the whole motor? Any help will be great.

Thanks,

John

OK, this morning I start it up and after calibration I can manually turn the spindle off and on without issue, which usually isn't the case, it usually errors out then also, but as soon as I run a program it does a tool change the head comes down and errors whenever the spindle is supposed to start. The error I get most is the Spindle drive fault Check Drive System, occasionally I get Agree System Failure.

Sounds like a faulty orient card. Will it orient in manual mode?

Alarm 01 (AL-01) Motor Overheat
Causes
Damaged motor fan, overload, motor cooler is dirty, loose connection.
Remedy
Replace parts, clean cooler, check connections, review cutting conditions.

Alarm 02 (AL-02) Excessive Speed Deviation
Causes
Overload, transistor module is damaged, loose connections, error with speed feedback signal, blown fuse.
Remedy
Replace parts, check connections, review cutting conditions.

Alarm 03 (AL-03) Blown Fuse in DC Link Section
Causes
Indicates that the fuse F4 in DC link is blown (models 30S and 40S).
Remedy
Check power transistors and replace fuse.

Alarm 04 (AL-04) Input fuse blown / Input power open phase
Causes
Defective transistor module, blown fuse.
Remedy
Replace parts, replace fuse.

Alarm 05 (AL-05) Control Power Supply Fuse Blown
Causes
Defective PCB, Abnormal power supply voltage.
Remedy
Check power supply, replace PCB, replace fuse.

Alarm 07 (AL-07) Excessive Speed
Causes
Incorrect parameter setting.
Remedy
Reset parameter value.

Alarm 08 (AL-08) High Input Voltage
Causes
AC power supply too high, incorrect setting of toggle switch for voltage setting.
Remedy
Change setting from 200V to 230V.

Alarm 09 (AL-09) Heat sink is overheated
Causes
Cooling fan is defective, overload, dust and dirty.
Remedy
Replace fan, review cutting conditions, clean parts.

Alarm 10 (AL-10) Input Power Voltage Low
Causes
Drop in input power, momentary power failure.
Remedy
Correct case and reset alarm.

Alarm 11 (AL-11) Overvoltage of DC Link Circuit
Causes
High power impedance, PCB or transistor module are defective.
Remedy
Check AC power, replace damaged parts.

Alarm 12 (AL-12) Overcurrent flows to DC Link Circuit
Causes
Output terminals or internal motor of motor is shorted, defective PCB or transistor module.
Remedy
Check connections, replace damaged parts.

Alarm 13 (AL-13) CPU Inter Data Memory Alarm
Replace PCB

Alarm 15 (AL-15)
Cause
Spindle switch /output switch alarm.
Remedy
Check sequence.

Alarm 16 (AL-16) RAM Abnormality
Causes
Defective RAM or PCB.
Remedy
Replace RAM, replace PCB.

Alarm 18 (AL-18) Program ROM sum check error
Causes
Defective ROM.
Remedy
Replace ROM.

Alarm 19 (AL-19)
Causes
Defective A/D convertor or PCB, loose connections.
Remedy
Replace A/D convertor, replace PCB, check connections.

Alarm 20 (AL-20)
Causes
Defective PCB, loose connections.
Remedy
Replace PCB, check connections.

Alarm 24 (AL-24)
Causes
CNC power off, defective optical cable.
Remedy
Turn power on, clean or replace optical cable, replace LSI, replace PCB.

Alarm 25 (AL-25)
Cause
See Alarm 24
Remedy
See Alarm 24

Alarm 26 (AL-26)
Cause
Defective signal level/line of spindle motor for C axis control, defective detector circuit for C axis control, incorrect parameter setting.
Remedy
Check signal level, connect signal cable securely, replace detector circuit, set correct parameter value.

Alarm 27 (AL-27)
Causes
Position coder signal line defective, incorrect parameter setting.
Remedy
Connect signal cable securely, replace signal cable, set correct parameter values.

Alarm28 (AL-28)
Cause
Defective signal level/line of spindle motor for C axis control, defective detector circuit for C axis control.
Remedy
Check signal level, connect signal cable securely, replace detector circuit.

Alarm 29 (AL-29)
Cause
Overload.
Remedy
Review cutting conditions.

Alarm 30 (AL-30)
Cause
Defective power transistor, defective PCB.
Remedy
Replace power transistor, replace PCB.

Alarm 31 (AL-31)
Cause
Motor constrained, defective motor speed reversion signal/signal cable
Remedy
Connect cable securely, replace cable.

Yes I can orient/lock the spindle. I c an actually turn it on in manual (most of the time), just when I go to auto it errors out.

Thank you for the reply,

John

OK, today I finally got some time to mess with it a bit. I traced the cables from the drive to the motor and found no cracks or anything. I wiggled them around and just repositioned them a bit, and it has been running just fine all day. I don't know if it is just deciding to run for a bit after having a couple months off or not, but this is the first time I have been able to get more than one cycle out of it in 2 months.

I guess now I need to maybe replace the cables. Does anyone know where I can find these, preferrably new ones?

I have a Hurco BMC /D with a Delta 20
Can not clear Spindle not ready alarm
There is a F200 code on the varispeed
Is there any hope
OMF1

What vfd is it?

Varispeed 626 VM3
Model CIMR-VMS27P5
SPEC#27P50 621207
Thanks

That's a Yaskawa drive. Have you the list of error codes? If not, I can tell you.

Yes it is and no I do not have them.
Thanks

It's an internal magnetic contactor failure. Look for the contactor (usually marked as an HV-75. A black block with terminals about 6"x4"x4") and see if it has any wiring issues. Also open the front cover of the drive and check the two fuses in the bottom (open the hinged panel to get to them) 1 1/4" glass fuses 4A). Check also that the spindle motor fan is running normally as the contactor and the fan are supplied by the two fuses).

Thank you.
I will let you know.

sir, i have an alarm fu in servo drive. pls tell me the rem,dy and tell the list of servo drive alarm .

sir
i have an alarm spindle fault check servo drive. and drive shows fu alarm what should i do ?