3 Attachment(s)
Mazatrol PC Fusion 640 Hang
Need Urgent help on it. My battery in my QT-6T machine died. I have since changed the battery and managed to load the win95 software. However, when i try to power on the green button, the "PS EMG" Led light up. Could anyone help me on this? Attached is the NC-Backup files that i have in the system. Could it be my parameters are lost? Please assist.... Anyone... Tks
PSEMG (red) LED on the HR082 card lights
Dear Ladies and gentlemen,
If the LED PSEMG on the HR082 card lights, this may have
following causes:The Emergency Stop Switch connected to the EMG connector
is ON (A contact), or the EMG connector is disconneted.
Remedy: Set the Emergency Stop Switch to the release (B contact) state. Check the connection to the EMG connector. (Maybe broken or loose).
Best Regards.
Gerd
Mazatrol PC Fusion 640 Hang
Hi,
For this type of HDD problems, best would be to take a Norton Ghost backup of the working HDD, using a USB-IDE Converter (or HDD casing as referred by some computer shops).
Norton Ghost 8.3 is freely available or you can buy Ghost 10 & above. We had tried it successfully on Mazatrol PC Fusion, Matrix, Meldas M625, M720 & M730.
If you have a Ghost backup of different machine but same control(PCFusion), you can recover if you have atleast
1) /NCBackup folder ( to load MainB s/w),
2) /M6Y_YMW/MPLC or TPLC (For the Machine & Coolant Menu) and
3) PLCMAcro backup(for ATC in some machine models).
Ghost image size will depend on the contents on HDD, but typically for Fusion it will start from 600MB & for Matrix 1.3GB. The Ghost s/w will prompt for the partition size if the new HDD is of higher capacity.
Another observation you can make to confirm HDD problem, is observe the status of Green LED on HR123/124, just below the Epson/Geode PCcard, after the 7-seg display on HR113/116 reach 1-2-3....6.
At 6 it starts reading the HDD.
Regards,
Girish
Mazatrol PC Fusion 640 Hang
Hi,
I believe it is L or R parameter problem. Normally in the backup from menu (Par, Tooldata, Toollife,etc) the L0-L255 and R1900-R2799 are not backed up. If you make SRAM clear(by Rotary Sw = 7), these values become zero, but cannot be regained with above backup.
Only reloading the SRAM back up (from mainte.exe) will recover them, if it was backed up when machine was ok. One should also be careful when re-loading the SRAM backup because if this backup was of a different NC version as compared to present, sometimes the data go in wrong location & create problem, as sometimes the Memory Map changes from Version to Version.
If the details of L & R para related to chucking type are not available, the ideal solution would be to note the values of L0-L255 and R1900-R2799, from a working machine, then compare with this machine. Change one which is different here, then check the alarm & restore back if no change & try next para whose value is different.
Please note that, it is is required to write these values from "I/O Monitor Write" menu in the Diagnosis.
The parameters are many in number, but those having a non-zero value will be limited, depending on the PLC. This exercise should not take more than 4-5 hours.
Regards,
Girish
Re: Mazatrol PC Fusion 640 Hang
Quote:
Originally Posted by
girishdk
Hi,
I believe it is L or R parameter problem. Normally in the backup from menu (Par, Tooldata, Toollife,etc) the L0-L255 and R1900-R2799 are not backed up. If you make SRAM clear(by Rotary Sw = 7), these values become zero, but cannot be regained with above backup.
Only reloading the SRAM back up (from mainte.exe) will recover them, if it was backed up when machine was ok. One should also be careful when re-loading the SRAM backup because if this backup was of a different NC version as compared to present, sometimes the data go in wrong location & create problem, as sometimes the Memory Map changes from Version to Version.
If the details of L & R para related to chucking type are not available, the ideal solution would be to note the values of L0-L255 and R1900-R2799, from a working machine, then compare with this machine. Change one which is different here, then check the alarm & restore back if no change & try next para whose value is different.
Please note that, it is is required to write these values from "I/O Monitor Write" menu in the Diagnosis.
The parameters are many in number, but those having a non-zero value will be limited, depending on the PLC. This exercise should not take more than 4-5 hours.
Regards,
Girish
Hi girish , my hdd is not getting detected even when open up my bios.
tried to copy all data and successfully backed it up. make one bootable of win 95 but still hdd is not getting detected.
Can you help me with this problem?
Re: Mazatrol PC Fusion 640 Hang
Need urgent help with my Mazak Fusion 640T controller.
Whenever i tried to start the machine, it shows non system disk or disk error.
I have tried to copy files to another hdd and boot it with win95, but still no hdd is getting detected.
What i get is non system disk error.
dont know what to do!
pls assist!
Thanks
Tej