Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
mbservice
Hi D Hardt
Do you have the programming manual for a Lynx 220LMS
We have the others but are missing this
The Doosan Operations Manual that came with the machine?
The Fanuc Programming Manual that came with the machine?
These are Doosan or Fanuc parts that are sold. The revenue from these manuals helps to pays for the respective companies to assist their customers with informative manuals and competent personnel that are able to go onto forums and assist those customers.
Please contact your local dealer with the serial number of your machine and they can get you a quote on replacement manuals.
I have NON-Part/NON-revenue manuals available (they cover a wide variety of uses. From repair to operation, and most are better oriented toward learning than the original manuals that ship with the machine.
The Parts Book, The Electrical Book, The Instruction Manual, and The Operations Manual: all ship with the machine and are considered a "PART" which is sold. I CAN NOT PROVIDE THOSE HERE.
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
T_clark
Hi I was wondering if I could get ANY information you have on a Doosan HP4000II? anything would be greatly appreciated!
Thanks!
Of the HP series, the most popular model is the 5000.
Most additional manuals use that machine as the reference material.
The procedures would be similar, but the part number would not be the same (correct part numbers would be gathered from the machine's parts manual)
1 Attachment(s)
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
Cml325
Hi , I'm also looking for a manual for
Daewoo DMV3016L for info on machine teardown for a spindle removal/installation.
Thanks, Cliff
The spindle section of this manual should be similar. (Note: Use the part numbers and process confirmation that you get by cross-referencing this information with your parts manual.
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
Louis_amecpro
DHardt,
We are in need of any/all manuals for Doosan S310N (Serial number LSA1226). Right now, we have only the electrical manual and Fanuc controller manual for this machine.
Local dealer tells us the manuals are no longer available for sell.
I know the machine is old but I hope you can help getting manuals in any way.
Regards,
Louis Gauthier
I have found a couple of available manuals that might be a potential match, or at least similar for your machine:
Potential of Electrical Manual:
If a Fanuc 0i-TB control: S280NHW
If a Fanuc 0i-TC control: S310NHW
Potential of Operations, Instruction, and Parts Book: S310NMLE
There is no guarantee that these will match your serial number; they are the only manuals available for the old S310 series.
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
mbservice
Hi D Hardt
Do you have the programming manual for a Lynx 220LMS
We have the others but are missing this
I can provide the manual we use in the training classes. It is comprehensive and well written. Let me know.
PS - It's NOT the programming manual that came with the machine, BUT, it actually covers material in a better way, IMO.
Re: Does anyone need service manuals for popular Doosan Machines?
Hi D Hardt
Do you have manuals for a Lynx 210 S/N L2002461 Y.O.M 2001
It has a FANUC 21it controller
Re: Does anyone need service manuals for popular Doosan Machines?
Do you have manuals for DAEWOO PUMA 200C?
Re: Does anyone need service manuals for popular Doosan Machines?
dhardt,
I need a full set of manuals for a 12S-B lathe.
Serial number PS100977.
Fanuc O-T control
I do not need programming or operation manual.
Need parts manual, maintenance manual and especially electrical.
I purchased the machine and the manuals were lost during shipment.
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
Tallg
dhardt,
I need a full set of manuals for a 12S-B lathe.
Serial number PS100977.
Fanuc O-T control
I do not need programming or operation manual.
Need parts manual, maintenance manual and especially electrical.
I purchased the machine and the manuals were lost during shipment.
The Parts Book, The Electrical Book, The Instruction Manual, and The Operations Manual: all ship with the machine and are considered a "PART" which is sold. I CAN NOT PROVIDE THOSE HERE.
These are Doosan parts that are sold. The revenue from these manuals helps to pays for the respective companies to assist their customers with informative manuals and competent personnel that are able to go onto forums and assist those customers.
Please contact your local dealer with the serial number of your machine and they can get you a quote on replacement manuals.
I have NON-Part/NON-revenue manuals available (they cover a wide variety of uses. From repair to operation, and most are better oriented toward learning than the original manuals that ship with the machine. (But note: I do not have NON-revenue manuals for a machine as old as a 12S. I might have a few relevant Tech-docs...but I do not know which ones, off hand.)
The Parts Book, The Electrical Book, The Instruction Manual, and The Operations Manual: all ship with the machine and are considered a "PART" which is sold. I CAN NOT PROVIDE THOSE HERE.
Re: Does anyone need service manuals for popular Doosan Machines?
i have an older Puma 2600Y S/N: ML0105-000313, i have an issue with an alarm NO. 2047 TURRET CLAMP SWITCH ALARM OR TURRET CONTROL UNIT ALARM, i have already followed the steps to fix the alarm by taking the back of the turret off and checking the distance form the dog and the switch(0.4 mm) i also unclamped and tried resetting the alarms and nothing happened, still have the same alarm. all i have is the operating manual and wiring diagram/ladder book, im also thinking im missing a manual or two,im fairly new to cnc repair seen but this is the first one that has me stumped. Any help would be most appreciated, Thanks
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
jhnlrs
Do you have the Spindle Maint./removal procedure for a Mynx 7500 Gear head?
Sorry. I do not.
1 Attachment(s)
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
the16vkid
i have an older Puma 2600Y S/N: ML0105-000313, i have an issue with an alarm NO. 2047 TURRET CLAMP SWITCH ALARM OR TURRET CONTROL UNIT ALARM, i have already followed the steps to fix the alarm by taking the back of the turret off and checking the distance form the dog and the switch(0.4 mm) i also unclamped and tried resetting the alarms and nothing happened, still have the same alarm. all i have is the operating manual and wiring diagram/ladder book, im also thinking im missing a manual or two,im fairly new to cnc repair seen but this is the first one that has me stumped. Any help would be most appreciated, Thanks
As you are postin here (this thread) I assume you would like a better service manual.
I attached one.
This is for the little brother of your machine. Procedures are similar, but use your parts book for the correct part numbers.
Re: Does anyone need service manuals for popular Doosan Machines?
thank you for the help on the 2600Y, i was able to get everything all in order. i do however have another issue that ive been looking at but doosan has been unresponsive in my efforts to get help, i have a puma 18 S/N PM180009, our tail stock has been having bearing issues and am looking to rebuild the tailstock. i was looking for any procedure for this process, i have several machine manuals but nothing to do with this particular machine, as always thank you for the help dhardt.
Re: Does anyone need service manuals for popular Doosan Machines?
I wonder if exist a manual for connection a Puma for example to Fanuc robot?
Re: Does anyone need service manuals for popular Doosan Machines?
Do you have one for MX, ST 35GS manual?
Re: Does anyone need service manuals for popular Doosan Machines?
Quote:
Originally Posted by
youngdoo
Do you have one for MX, ST 35GS manual?
I notice that you are in Korea. Doosan Korea has the same (and more) manuals, written in Hangul.
Would you rather have those?