Mach3 G-Code-Ripper not working

Printable View

10-23-2018, 08:17 AM
madmac4u

Mach3 G-Code-Ripper not working

I have 4-axis 6090 CNC from china,
i am using "G-Code-Ripper" to work with uneven surface copper pcb.
but when i run the file.ngc file in mach3 the output in the file gives similar values for each axis,
though while running the probing it shows proper Z values on Mach3 interface.

the output file looks like this
"
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
"

Please help me find out the problem.
Thank You.
08-03-2019, 11:47 PM
zl1lds

Re: Mach3 G-Code-Ripper not working

Hey, did you ever receive a fix for this. I have a similar issue if the board is very closely level. If it's a lot out of sync then the output file seems to work,
08-04-2019, 03:54 AM
he1957

Re: Mach3 G-Code-Ripper not working

Try lowering the accuracy values in General Settings.
09-04-2019, 01:20 AM
Aquiles_81

Re: Mach3 G-Code-Ripper not working

Quote:

Originally Posted by he1957

Try lowering the accuracy values in General Settings.

I have the same problem, were you able to solve it?
06-16-2020, 04:23 PM
basilio

Re: Mach3 G-Code-Ripper not working

did you ever receive a fix for this?
07-05-2020, 11:21 PM
scorch

Re: Mach3 G-Code-Ripper not working

Quote:

Originally Posted by madmac4u

I have 4-axis 6090 CNC from china,
i am using "G-Code-Ripper" to work with uneven surface copper pcb.
but when i run the file.ngc file in mach3 the output in the file gives similar values for each axis,
though while running the probing it shows proper Z values on Mach3 interface.

the output file looks like this
"
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
54.97500,21.67500,-0.03750
"

Please help me find out the problem.
Thank You.

This is a problem with MACH3 and/or the controller board you are using. Other people have reported problems like this. At least one fixed it by upgrading the firmware on the controller.

I don't use MACH so I don't know more than that.