-
3 Attachment(s)
Help with Novusun NVUM V2 USB control card
I bought the NVUM v2 Control board in a pakcgae deal with the TB6660 Stepper drivers. These are wired to the 4 Nema 23 Stepper motor on a CNC build similar to the Workbee. I configured everything according to manuals and it was acting like it was losing steps. Mark start point, do a toolpath and when it ends and goes back to Home, it was about 12 mm off on the X axis. Ive since tried to reconfiguire the settings and verified, and verified and Now when I launch Mach3 with the Plugin installed and NVUM powered on, its giving me a message about selecting a BIN file If I dont select one it says upgrade failed and continuers to ask for a BIN file. IN my experience a BIN file would most likely be a firmware flash for the Controller card. Where do I find this, since the Parent site NVCNC.net has nothing like that to download.and the supplier in china Aliexpress (jacky Bulk Man 3d) is Not responding to my email?
Attachment 395826Attachment 395828Attachment 395830
-
It happened to me today, now neither USB works anymore.I think you have to rewrite the firmware.
-
Quote:
Originally Posted by
kmargos
It happened to me today, now neither USB works anymore.I think you have to rewrite the firmware.
I have same problem, agere can i find the bin file?
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
Winterdragon
I bought the NVUM v2 Control board in a pakcgae deal with the TB6660 Stepper drivers. These are wired to the 4 Nema 23 Stepper motor on a CNC build similar to the Workbee. I configured everything according to manuals and it was acting like it was losing steps. Mark start point, do a toolpath and when it ends and goes back to Home, it was about 12 mm off on the X axis. Ive since tried to reconfiguire the settings and verified, and verified and Now when I launch Mach3 with the Plugin installed and NVUM powered on, its giving me a message about selecting a BIN file If I dont select one it says upgrade failed and continuers to ask for a BIN file. IN my experience a BIN file would most likely be a firmware flash for the Controller card. Where do I find this, since the Parent site NVCNC.net has nothing like that to download.and the supplier in china Aliexpress (jacky Bulk Man 3d) is Not responding to my email?
Attachment 395826Attachment 395828Attachment 395830
I have had the same problem after six months use started getting load BIN file message. Anyway after much searching found BIN file and loaded it all good again. the BIN file can be downloaded from following link on the Novusun web page. https://www.nvcnc.net/nvum.html Button bottom middle of screen. Or direct link https://www.nvcnc.net/pdf/nvum.bin.rar
John
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
Galoptic
I have had the same problem after six months use started getting load BIN file message. Anyway after much searching found BIN file and loaded it all good again. the BIN file can be downloaded from following link on the Novusun web page.
https://www.nvcnc.net/nvum.html Button bottom middle of screen. Or direct link
https://www.nvcnc.net/pdf/nvum.bin.rar
John
I found this board on a Search, not here however or I would not be asking this. How many people are using this control board? NVUM USB MACH3 Card V2
problems or pitfalls? USA Vendors?
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
if you post on the Mach forum with a NVUM board you will be informed that the company is on the 'Hall of Shame' list for peddling
pirate Mach3 copies and you will be denied assistance.
I don't get you Yankees....you have a trade war going on with China claiming they are undermining your economy and yet here you are trying to buy
this rubbish? You have manufacturers in the US making superb boards with full back-up...yet you want to save a few dollars at American workers
expense?.
NVUM, or whatever they call themselves, DO NOT SUPPORT their products, if they've got your money you take 'take a hike' as far as they are concerned.
Craig
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
joeavaerage
Hi,
if you post on the Mach forum with a NVUM board you will be informed that the company is on the 'Hall of Shame' list for peddling
pirate Mach3 copies and you will be denied assistance.
I don't get you Yankees....you have a trade war going on with China claiming they are undermining your economy and yet here you are trying to buy
this rubbish? You have manufacturers in the US making superb boards with full back-up...yet you want to save a few dollars at American workers
expense?.
NVUM, or whatever they call themselves, DO NOT SUPPORT their products, if they've got your money you take 'take a hike' as far as they are concerned.
Craig
Hey guess what you do not need to use the pirated version IF you buy a license. That is what I did and right on their website they tell you that. Show me a USA Made board with USB interface built in?
Or this https://buildyourcnc.com/item/electr...ach3-USB-Board is it made in USA?
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
no that board is Chinese made and is absolute junk, even by comparison to the NVUM. See any number of posts on the Mach forum about this board
and its many clones.....no manufacturer support at all.
PMDX-412 is a single port USB connected motion controller, US made and supported.
I would not recommend USB, it is just too noise prone. Get an Ethernet connected board like an ESS, again US made and supported with a dedicated
forum, Mach3 AND Mach4 compatible. Retails at $180USD so is little more than the NVUM.
Craig
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
joeavaerage
Hi,
no that board is Chinese made and is absolute junk, even by comparison to the NVUM. See any number of posts on the Mach forum about this board
and its many clones.....no manufacturer support at all.
PMDX-412 is a single port USB connected motion controller, US made and supported.
I would not recommend USB, it is just too noise prone. Get an Ethernet connected board like an ESS, again US made and supported with a dedicated
forum, Mach3 AND Mach4 compatible. Retails at $180USD so is little more than the NVUM.
Craig
It is cost that a lot look at and the NVUM is very good as far as cost goes I have helped some user's get up and running with these units, most already have Mach3 so are not using the software that comes with it
They are not junk as you say and are very well made, you obvious have not had your hands on one, electronically challenged user's are always going to say they are junk if they can't get them running and yes in most cases the Ethernet model is the best choice but the USB can be just as good in some situations, the ESS is the only one that is a comparison and user's have problems setting that up as well, with around the same amount of help so it is all about cost more than anything else
-
Re: Help with Novusun NVUM V2 USB control card
Thanks Mac for chiming in.
If I have a license for both Mach3 & 4 does that make the board ok to use Craig? I have an industrial rated USB shielded cable I use now on my keyboard with my Mach4 machine and its fine.
My new machine will not have a spindle or VFD and because of a medical event in my life I have downsized a lot. You do what you need to do.
The other board I referenced above is sold by a US Distributor with US support, how is that not a good deal?
Our dear president has pissed off just about everyone in the world including our former allies. The Chinese who now make our pharmaceuticals and medical masks and other supplies are now our enemy, but wait.. now people are dying from a lack of those same supplies. Lets be friends again. Craig, they make all our computers, cell phones, tvs' and yes even MRI machines. etc and other electronics so how can a CNC control board be junk, just because its made in China?
BTW I am looking at the PMDX series and I may go that route because I would rather run Mach4.
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
Quote:
If I have a license for both Mach3 & 4 does that make the board ok to use Craig?
Well yes according to mactec54, although I don't know whether you will receive any support on the Mach forum.
It still begs the question why you'd rather support Chinese workers rather than American workers....especially as American manufacturers support their products.
When it comes to Chinese boards you send an email to China......in a galaxy far far away.
Quote:
The other board I referenced above is sold by a US Distributor with US support, how is that not a good deal?
It may be sold in the US but is made in China and if you can find any manufacturers support ANYWHERE you are doing better than hundreds
of people on the Mach Forum.
Craig
-
1 Attachment(s)
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
joeavaerage
Hi,
Well yes according to mactec54, although I don't know whether you will receive any support on the Mach forum.
It still begs the question why you'd rather support Chinese workers rather than American workers....especially as American manufacturers support their products.
When it comes to Chinese boards you send an email to China......in a galaxy far far away.
It may be sold in the US but is made in China and if you can find any manufacturers support ANYWHERE you are doing better than hundreds
of people on the Mach Forum.
Craig
Craig, the board is supported by a USA seller, did you not see the Link I put up? Yes I am looking at the PMDX 416 as I would like to run Mach4.
A picture of the board you say is made in China?
Attachment 438740
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
wmgeorge
Thanks Mac for chiming in.
If I have a license for both Mach3 & 4 does that make the board ok to use Craig? I have an industrial rated USB shielded cable I use now on my keyboard with my Mach4 machine and its fine.
My new machine will not have a spindle or VFD and because of a medical event in my life I have downsized a lot. You do what you need to do.
The other board I referenced above is sold by a US Distributor with US support, how is that not a good deal?
Our dear president has pissed off just about everyone in the world including our former allies. The Chinese who now make our pharmaceuticals and medical masks and other supplies are now our enemy, but wait.. now people are dying from a lack of those same supplies. Lets be friends again. Craig, they make all our computers, cell phones, tvs' and yes even MRI machines. etc and other electronics so how can a CNC control board be junk, just because its made in China?
BTW I am looking at the PMDX series and I may go that route because I would rather run Mach4.
Yes if you want to run Mach4 then you will need one of the other boards both are not always easy to get up and running the smooth stepper is the best choice so far for Mach4 users, the PMDX I have not seen any negative posts about it but there may not be many user's also
If you did get a NVUM get the Ethernet connect
What's the name of that board
-
Re: Help with Novusun NVUM V2 USB control card
Bitsenser . I am inclined to go with PMDX ones as I like Mach4.
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
among its other names is RnR Motion and it is has no manufacturer backup.......if you don't believe me go and read the dozens of posts
about them on the Mach Forum.
PMDX is the polar opposite and enjoys the BEST reputation for back up on any Mach ready board.
The ESS by Warp9 must come a close second.......have a look at the efforts of Andy, the Warp9 support man on the Warp9 forum,
8 hours a day, five days a week.
Craig
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
among its other names is RnR Motion and it is has no manufacturer backup.......if you don't believe me go and read the dozens of posts
about them on the Mach Forum.
Once again... it has support here : https://buildyourcnc.com/item/electr...ach3-USB-Board
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
wmgeorge
Bitsenser . I am inclined to go with PMDX ones as I like Mach4.
Ok I found it on line don't know that controller Board but for $20 you can't expect much, I may get one when I have time, to have a play with it and see what it can do, the NVUM is a much better Board controller I'm sure it would work for most simple machine setups, the PMDX or the ESS is your best choice for Mach4 though
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
wmgeorge
Yes it is well documented and if you don't need anymore than 100KHz output ( which most don't ) is really a good deal for $20
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
Quote:
Once again... it has support here
Then have at it. Don't believe any of the dozens of posts about them on the Mach forum.
Craig
-
Re: Help with Novusun NVUM V2 USB control card
HI,
what kind of support you have from linked seller? The board at China costs less than $20 (approx 13€ with shipping).
Just take a look at the Mach forum. It's up to you that live in belief that paying $90 for a $20 product will provide you a quality support.
-
2 Attachment(s)
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
ZASto
HI,
what kind of support you have from linked seller? The board at China costs less than $20 (approx 13€ with shipping).
Just take a look at the Mach forum. It's up to you that live in belief that paying $90 for a $20 product will provide you a quality support.
Guy, ah it sells as above on the link I posted for $89 in the USA, so what the hell are you talking about!! The NVMU or whatever I did not buy! The one below that is what I have ordered.
Attachment 438782
Attachment 438784
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
Quote:
Guy, ah it sells as above on the link I posted for $89 in the USA
That means you are being ripped, they are available for $20 elsewhere. To be honest I think $20 is a rip too.
Craig
-
Re: Help with Novusun NVUM V2 USB control card
Ok Craig the floor is all yours... have at it. Thanks for your help.
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
joeavaerage
Hi,
That means you are being ripped, they are available for $20 elsewhere. To be honest I think $20 is a rip too.
Craig
They may not be the same boards the cheap one's may be copies of the original manufactured board this happens a lot $89 sounds about right for a 100Khz board if you compare it with the 100Khz UC100 it is a little cheaper than the UC100 at $89 so may not be a rip off at all get the facts correct, what you are saying is not credible as you don't have hands on experience with this board
Remember electronically challenged installer's will have trouble with any system no matter how fool proof they are made what you see on the forums is typical of people in need of help and 99% are electronically challenged
I have no use for one of these boards but will buy one just to see if they are bad or not
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
Galoptic
I have had the same problem after six months use started getting load BIN file message. Anyway after much searching found BIN file and loaded it all good again. the BIN file can be downloaded from following link on the Novusun web page.
https://www.nvcnc.net/nvum.html Button bottom middle of screen. Or direct link
https://www.nvcnc.net/pdf/nvum.bin.rar
John
Hello Galoptic
I would like to ask you where you finded bin.file for novusun. I am looking for the bin file for NVEM V2. I suspect that after the connection analog output of spindle to the analog input of inverter the firmware was cleared. Something goes wrong. NVEM worked ok ealier after this situation NVEM not respodnds.
Thank you in advance for your responce
-
Re: Help with Novusun NVUM V2 USB control card
Друг привет.У меня тоже такая проблема возникла.И теперь ни один компьютер не видит устройство.Ты решил эту проблему ?
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
pociu
Hello Galoptic
I would like to ask you where you finded bin.file for novusun. I am looking for the bin file for NVEM V2. I suspect that after the connection analog output of spindle to the analog input of inverter the firmware was cleared. Something goes wrong. NVEM worked ok ealier after this situation NVEM not respodnds.
Thank you in advance for your responce
Files for NVEM here https://www.nvcnc.net/nvem.html
-
Re: Help with Novusun NVUM V2 USB control card
Hi Streumer,
the NVUM-bin file link above has been broken for a while (404 Not Found). it would be a great help if you have the bin file on google drive or a sure download link! I can't find it anywhere online.
thank you
-
Re: Help with Novusun NVUM V2 USB control card
I can sum this up in 2 mins.
The website likely hasn't been updated in last 10 years.
They never patented the controller.
The ones you buy now are copies of the original.
Support does not exist.
-
Re: Help with Novusun NVUM V2 USB control card
Quote:
Originally Posted by
aligaman
Hi Streumer,
the NVUM-bin file link above has been broken for a while (404 Not Found). it would be a great help if you have the bin file on google drive or a sure download link! I can't find it anywhere online.
thank you
pm ME
-
Re: Help with Novusun NVUM V2 USB control card
Hi,
This link to nvum firmware bin file does not work. COuld you please send the file or a valid link?
I am very in need to fix my novusun cnc controller.
thanks,