Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
Moriduri
Hi, have you solved this issue? I have an ACS806 and 57BL180D servo from Leadshine that suffer from a similar problem, the servo works below 530 rpm (the following error is high but it keeps spinning, without load) but if i exceed 530 rpm than the following error quickly jumps to the limit and stops the motor.
Thanks, Matteo.
No, I did not solve this issue. I tried tune these drivers (I have two and both have this issue) many times but without success. Even worse is fact that the following error is not constant but is depending on the actual speed. So In my opinion these drivers are totally useless for accurate positionig. You can see similar thread here.
1 Attachment(s)
Re: Leadshine technical support available on CNCzone.com
Where does this Larger Gnd wire go that is in the encoder cable?https://www.cnczone.com/forums/attac...d=406802&stc=1
Re: Leadshine technical support available on CNCzone.com
That should be the shield (braid) ground if its shielded (with braid). Normally this is grounded to chassis at only one end. In a star ground configuration using the cabinet as the reference it would be grounded here. If your system (encoder end) is grounded to chassis with a similar arrangement seen here but at the motor end put some insulation on this end to avoid a potential ground loop.
Re: Leadshine technical support available on CNCzone.com
I'll just leave it disconnected for now then, You would think that these encoder cables with 7 wires would be mentioned somewhere. There is not continuity with the multi-meter with the port end outer sheath. next best bet would be to try all the port holes to see if i get a signal.
Re: Leadshine technical support available on CNCzone.com
I'd definitely put some insulation on that exposed wire.
Re: Leadshine technical support available on CNCzone.com
Re: Leadshine technical support available on CNCzone.com
hi.
i have es-m32320 and es-d508 drive and i want to use PIC18f4550 as pulse generator . my problem is , how can i implement acceleration with this spec?
i need soft starting and soft stopping of motor.
thank for your help
Re: Leadshine technical support available on CNCzone.com
Glad to see this section. Maybe someone can help. I purchased 4 DM860e drivers from automation direct. I have them hooked up to my Pokeys57cnc, but the motor will just click a little and try to move, but no movement. Curious about your suggested wiring. I have hybrid NEMA23 8 wire steppers. I am just lost at this point. I hooked up the drivers per Pokeys tutorials on Youtube, but with no success.
Thanks in advance,
Shane
Re: Leadshine technical support available on CNCzone.com
Hi Shane,
Thank you for supporting Automation Direct.
It seems that the drive DM860E does not receive the normal pulse/dir signal please check if there was any correct 5v pulse signal output from Pokeys57cnc controller?Max.frequency 200khz).
You can try to move motor shaft by hand when power on to check if your motor is locked by driving current , and the NEMA23 stepper motor with 8-wire, do you use parallel connection or serial connection? Don't connect a wrong wire, double check according to your drawing. If any question or support just let us know, thanks.
Best regards.
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
Leadshine
Hi Shane,
Thank you for supporting Automation Direct.
It seems that the drive DM860E does not receive the normal pulse/dir signal please check if there was any correct 5v pulse signal output from Pokeys57cnc controller?Max.frequency 200khz).
You can try to move motor shaft by hand when power on to check if your motor is locked by driving current , and the NEMA23 stepper motor with 8-wire, do you use parallel connection or serial connection? Don't connect a wrong wire, double check according to your drawing. If any question or support just let us know, thanks.
Best regards.
Got it figured out. Was off a pin when I soldered my connector through the cabinet.
2 Attachment(s)
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
548cidakota
Got it figured out. Was off a pin when I soldered my connector through the cabinet.
I had an enlightenment.
After so many years I think I understand why I lose steps in the motor reversal
see the pic
t2: DIR must be ahead of PUL active edge by at least 5 ?s to ensure correct direction.
t3: Pulse width not less than 0.85 ?s;
t4: Low level width not less than 0.85 ?s.
I have read many posts but I think this is the solution
in linuxcnc the BASE_PERIOD must be modified
when I have some time I'll try this solution
https://www.cnczone.com/forums/attac...d=442898&stc=1
Re: Leadshine technical support available on CNCzone.com
Hi Gantarone,
For the control signal,there is strict time sequence to make sure the drive can recognize signal correctly. PS:Different drivers have different timing requirements
Usually, the DIR signal should ahead PUL signal at least 5us, even 10us so that the drive can accurately determine the direction of the motor first, motor will not lose steps when reverse. Also the same for ENA If you use.
Thank you for supporting Leadshine products!
Re: Leadshine technical support available on CNCzone.com
Hello,
I have problems using ProTunerCS V3.1 on Wind10 (laptop).
When I tried to use the scope tool-start, it works for some seconds and then it gets closed.
Any idea what to do? I could not find this software on the chinese web, it doesn't exist.
Thanks.
Re: Leadshine technical support available on CNCzone.com
Hello,Please let me know the model and serial number of your drive?
CS series is designed for overseas customers so it's not released in China market there is no English manual and software on chinese website.
Where did you buy the drive and motor? Thanks.
Re: Leadshine technical support available on CNCzone.com
I am fixing a GWeike laser engraver for a friend. The two Z axis steppers just vibrate back and forth. The LED on the Leadshine ME872 stepper driver is green. I moved the cables to the Y axis and changed the DIP switches to match the Z axis and the steppers work fine. Is there anything I can do to possibly repair the ME872, and if not, how would I purchase a new one? Thanks.
Re: Leadshine technical support available on CNCzone.com
I was wondering what the pinout for the serial RJ11 connector is on the HBS86H?
I cannot find it in any documentation from Leadshine?
Thanks.
Re: Leadshine technical support available on CNCzone.com
Hello , I just start having an issue with my MX4660, I have 3 push buttons connected to input 1, 2 and 3 fot cycle start, feed hold and stop cycle, +12v connected to OPTO1. They were working right but suddenly they are no longer working, I verified the volt between push buttons terminals (NO push buttons) they show 11.2v in normal state and drop to 2volt when I press the push butons. Any help where should i need to look for
Re: Leadshine technical support available on CNCzone.com
Hello Leadshine,
Is it possible to buy replacement board for stepper motor driver DMA860H ? How much ?