-
Leadshine technical support available on CNCzone.com
Leadshine is glad to announce that we will start to provide technical support on CNCZone to users who have bought from us directly, or through our authorized distributors out side of China at Distribution Network. As the largest stepper drive and easy servo (closed stepper) system designer and manufacturer in the world, Leadshine products have been widely implemented in tens of industries including very high sales in CNC industries (mills, routers, plasma, lathe, laser cutter, waterjet...). Because the popularity of our products, there are a lot of replicas and fake Leadshine products sold online from eBay, Amazon... For this reason, Leadshine will not provide technical support or warranty to products bought through those source. You are welcome to post your questions here in this Leadshine forum. You can also go to Leadshine website at www.leadshine.com or www.leadsihineusa.com to find manuals, software, datasheets..., which could help to solve your technical issues.
-
Re: Leadshine technical support available on CNCzone.com
Glad to see a presence here from Leadshine.
I recently purchased the following items from Americanmotiontech.com which is linked from your website.
ES-MH23480 Easy Servos
ES-DH1208 drives
CABLEH-RZ5MO cables
CABLEH-BM5MO cables
My question is that the cables were described as "shielded" but when I peeled back the heat shrink on the end of the jacket I cannot see the typical braided shielding.
What is you take on that fact?
Is it shielded or not?
Thanks,
Rob
Sent from my BNTV600 using Tapatalk
-
Re: Leadshine technical support available on CNCzone.com
Hi Rob
Thank you for purchasing Leadshine products .
The motor power cable is not shielded ,but the encoder cable is shielded. you can check it .
Any other problem ,kindly leave me message or email me .
John
[email protected]
Leadshine Technical Support
-
Re: Leadshine technical support available on CNCzone.com
How can we know is it fake or not? I bought from ebay HBS507 driver and 573HBM20-1000 motor but I cannot find manual or software for that drive.
Regards,
Marijan Jakara
-
Re: Leadshine technical support available on CNCzone.com
Hi Marijan
Leadshine is No.1 for stepper products in China,anf there are many fake products online .we don't have anti-counterfeit label on products ,so i am not your products are Leadshine or not .
And HBS507 driver and 573HBM20-1000 are sold for Chinese local market ,not for international market .so please contact your supplier firstly , i think they will send the information as you want .
If you like Leadshine products ,please contact Leadshine directly or Leadshine distributors . we have many distributors in many countries. i think you will get good after sale service and good products .
-
Re: Leadshine technical support available on CNCzone.com
Hi I have the Leadshine HBS86H driver and the HBS507 driver. I can run them both with Protuner fine however when I use my mach3 motion controller only the HBS507 is turning the HBS86H will not turn. Do you know why this is? maybe it needs higher step/dir signal voltage?
Thanks,
layman94.
-
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
mjakara
How can we know is it fake or not? I bought from ebay HBS507 driver and 573HBM20-1000 motor but I cannot find manual or software for that drive.
Regards,
Marijan Jakara
Hi I bought the same driver off of ebay also. If you are English speaking this may help you.
- For the manual just go to Leadshine Technology - Home and download the manual for the ES-D508 drive. They are the same as far as I can tell and I have had no problems using it.
- If you want to use Protuner (I tried the ES-D508 version it did not work for me) you are going to have to go to www.leisai.com. It will be necessary to have the Leadshine Technology - Home
webpage open at the same time.
- The leisai page is ONLY in Chinese so you will have to navigate using the leadshine.com page as a reference.
- You will find the protuner for the HBS series version 1.3 download this. This is also ONLY in Chinese.
- To use this you will have to get the manual for the ES-D series protuner for reference it has the same layout.
Hope this helps.
regards,
layman94
-
Re: Leadshine technical support available on CNCzone.com
Hi mjakara I recently purchased the same motor and driver COMBO from EBay HBS507 would you be able to email me the software for that driver or a direct link to do so myself. I went to www.leisai.com and was unsuccessful.
Thanks in Advance
-
Re: Leadshine technical support available on CNCzone.com
Hello,
How to wire THC Proma SD with Leadshine MX4660? I use plasma cutter cut70 Stahlwerk. Thanks.
-
Re: Leadshine technical support available on CNCzone.com
Here are the addresses for the Leadshine protuner for ESD-508 and HBS507
ES-D508 protuner
- ES-D Series Easy Servo Drives / Closed Loop Stepper Drives | Leadshine
- it looks like the same drive , but it didn't work for me.
HBS507 protuner
- http://leisai.com/product/detail.asp...odecode=101030
- It is under HBS507_setup. it is 14674KB
- It worked for me though it is in Chinese only. I just downloaded the manual for the ES-D series and navigated with that, It is the same layout.
ES-D508 protuner manual
-http://leadshine.com/productdetail.aspx?type=products&category=easy-servo-products&productype=easy-servo-drives&series=ES-D&model=ES-D508
-it is under ES-Dsm_V1.0.pdf
regards,
Layman94
-
Hi I have a mx3660. The instructions say to use a shunt regulator to be used. Any recommendations on a shunt regulator?
-
Re: Leadshine technical support available on CNCzone.com
I have a MX3660 bought through XZero as part of my Raptor CNC package. It has run well since I began using it last November. Today, out of the blue, it my CNC stopped and the limit switch lights dimmed, I smelled electrical burning coming from the MX3660. My power supply seems to be fine, and my smooth stepper will run if I disconnect the power at the MX, so it seems like it has failed for some reason. How do I initiate warranty service?
-
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
Layman94
Hi I bought the same driver off of ebay also. If you are English speaking this may help you.
- For the manual just go to
Leadshine Technology - Home and download the manual for the ES-D508 drive. They are the same as far as I can tell and I have had no problems using it.
- If you want to use Protuner (I tried the ES-D508 version it did not work for me) you are going to have to go to
www.leisai.com. It will be necessary to have the
Leadshine Technology - Home
webpage open at the same time.
- The leisai page is ONLY in Chinese so you will have to navigate using the leadshine.com page as a reference.
- You will find the protuner for the HBS series version 1.3 download this. This is also ONLY in Chinese.
- To use this you will have to get the manual for the ES-D series protuner for reference it has the same layout.
Hope this helps.
regards,
layman94
Layman94. Have you tried to use ES-D508 driver (witch is International version of HBS507), save the settings to file from english version of ProTuner just to open Chinese version of ProTuner and load the setting from the file to HBS507?
Theoretically it schould work.
Sent from my SM-T815 using Tapatalk
-
Re: Leadshine technical support available on CNCzone.com
I have a Camaster cnc, Why would leadshine MX4660 drive blow from hittng the estop. This seems to be a common problem. Any fixes woul be appreciated
-
Re: Leadshine technical support available on CNCzone.com
hutch...
It is well known that dc steppers generate voltage when they are moved when not under power. Numerous drives on numerous brands have blown when axes are moved by hand. Imagine the current generated if the machine was executing a rapid move of a few hundred inches per minute and the estop was activated, which of course removes power to the drives. Once the back EMF gets into the drive, it lets the magic smoke out. Blown drive.
2 fixes: 1) Forget about the estop and use the spacebar. Too many users think that the Estop is the "everyday stop", its not, never has been. 2) Search for and find the Leadshine tech document that specs a couple $40 aluminum caps, or an even more expensive shunt to absorb the generated voltage, and install one setup.
-
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
islaww
2) Search for and find the Leadshine tech document that specs a couple $40 aluminum caps, or an even more expensive shunt to absorb the generated voltage, and install one setup.
http://www.cnczone.com/forums/attach...2&d=1447075158
-
Re: Leadshine technical support available on CNCzone.com
Thanks Gerry....
You have a mind like a steel trap!
GC
-
Re: Leadshine technical support available on CNCzone.com
Just decent Google skills. I'd never seen that info before. ;)
I was curious, so went looking for it.
-
Re: Leadshine technical support available on CNCzone.com
Hi ,
I bought a 3x BLM57130-1000 and ACS306 the problem :
do not make a complete revolution during the reverse direction (like backlash)
I tried the ProTuner program (from Leadshine )but without result .
(soon I will attach a video)
Please Help!!!!
Simone
-
Re: Leadshine technical support available on CNCzone.com
this is the videohttps://www.youtube.com/watch?v=adgf...ature=youtu.be
is BLM57180-1000 and ACS606 same BLM57130-1000
-
1 Attachment(s)
Re: Leadshine technical support available on CNCzone.com
I'm trying to add a 4th axis to the MX3660 but I can't get it to work.
Can anyone tell me what I'm doing wrong (maybe om reading the schematics wrong?)
I have connected it like this:
MX3660 to stepper driver:
(Output 1+) to (DC+)
(Output 1-) to (Pul +)
(Output 2+) to (DC+)
(Output 2-) to (Dir +)
((Pul- and Dir- to GND))
Attachment 354232
-
Re: Leadshine technical support available on CNCzone.com
My MX4660 just stopped working all of the sudden. The LEDs ont eh drivers are dim, and flickering. Power supply is good at 36 V into the MX4660.
-
Re: Leadshine technical support available on CNCzone.com
Hi, I just received some of #Leadshine integrated easy servo motors(Leadshine easy servo motors / stepper motors with encoders) which were purchased from AMT.
I am able to connect to them in the protuner program, but when I try to access the settings or do a motion test, the motor will start to move as commanded, and take window pops up that the program has crashed.
Any idea what could be causing this?
I am using the FTDI usb to serial cable which was purchased along with the motors from AMT. The motors were connected to a power supply set to 26V. Lastly, the machine that the protuner program was running on is running windows 10 as I do not have access to a windows 7 machine.
-
Re: Leadshine technical support available on CNCzone.com
Hi all. I'm trying to set up the ACS606 drive along with the BLM57090 servomotor but I'm not able to get a smaller following error than 400 steps at a constant speed of 2000 RPM. I'm a little confused because of the ACS606 datasheet stated that the position following error should be +/- 1 count. Does anyone have a similar experience?
-
Re: Leadshine technical support available on CNCzone.com
Quote:
Originally Posted by
K_73
Hi all. I'm trying to set up the ACS606 drive along with the BLM57090 servomotor but I'm not able to get a smaller following error than 400 steps at a constant speed of 2000 RPM. I'm a little confused because of the ACS606 datasheet stated that the position following error should be +/- 1 count. Does anyone have a similar experience?
Hi, have you solved this issue? I have an ACS806 and 57BL180D servo from Leadshine that suffer from a similar problem, the servo works below 530 rpm (the following error is high but it keeps spinning, without load) but if i exceed 530 rpm than the following error quickly jumps to the limit and stops the motor.
Thanks, Matteo.