584,846 active members*
4,361 visitors online*
Register for free
Login

Search:

Type: Posts; User: gugu

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    533

    Re: Fanuc SRAM Backup Stuck

    I thought that since my machine is Twin Spindle, it works like 2 machines in one, so the first 2 files would be for one machine, and the other 2 files would be for the other machine. I didn't get...
  2. Replies
    9
    Views
    533

    Thank you for taking time to help. The machine...

    Thank you for taking time to help.
    The machine works fine, so i wouldn't want to work with the SRAM and risk loosing parameters and making the machine unusable. I just want to make an SRAM backup...
  3. Replies
    9
    Views
    533

    Fanuc SRAM Backup Stuck

    Hi,

    I have 3 Nakamura Tome WT250 lathes, twin spindle, twin turret, Fanuc 18i TB control.
    I made SRAM backups for the machines. For 2 of them, the backup works ok, it writes 4 files for every...
  4. Replies
    6
    Views
    31,079

    Re: 750 Serial spindle link error

    In my case, the 2 resistors R51 and R52 on the DC buss were open. The resistors are on the main board of the Spindle Amplifier (not on the communications board).
    Replace the 2 resistors at it might...
  5. Replies
    5
    Views
    3,447

    Re: fanuc spindle fuse on dc link blown

    In my case, the 2 resistors R51 and R52 on the DC buss were open. The resistors are on the main board of the Spindle Amplifier (not on the communications board).
    Replace the 2 resistors at it might...
  6. Replies
    2
    Views
    5,743

    Re: Help with Error 751 Spindle 1 AL-03

    In my case, the 2 resistors R51 and R52 on the DC buss were open. The resistors are on the main board of the Spindle Amplifier (not on the communications board).
    Replace the 2 resistors at it might...
  7. Replies
    3
    Views
    4,867

    Re: Spindle Drive Alarm AL-03??

    In my case, the 2 resistors R51 and R52 on the DC buss were open. The resistors are on the main board of the Spindle Amplifier (not on the communications board).
    Replace the 2 resistors at it might...
  8. Replies
    6
    Views
    1,896

    Re: AL-03 Alarm on AC Drive

    In my case, the 2 resistors R51 and R52 on the DC buss were open.
    Replace the 2 resistors.
  9. Replies
    12
    Views
    4,002

    Re: Hurco Hawk 5M machine specs

    Hi Guys,

    I think i have a problem with my Hurco Hawk 5M. When i try to run a Tap cycle, i constantly get the error "Speed Too Low" if i try to use a speed under 550 RPM. With a drill i can use low...
  10. Thread: Hurco MD3

    by gugu
    Replies
    5
    Views
    1,999

    P.S. I'm located in Europe, in Romania. But i can...

    P.S. I'm located in Europe, in Romania. But i can ship parts if you need them, or even the whole machine. Shipping the machine across Europe should be around 1.000 euro, i guess...

    I also scrapped...
  11. Thread: Hurco MD3

    by gugu
    Replies
    5
    Views
    1,999

    Re: Hurco MD3

    Guys, i'm selling my Hurco MD3 if anyone is interested. We had this machine in our company for more than 10 years and it NEVER worked. I think there are some wiring or electrical problems that we...
  12. Replies
    4
    Views
    1,517

    Re: 1989 Hurco Km3P retrofit

    Thanks for the reply. I'll contact him.
  13. Replies
    4
    Views
    1,517

    Re: 1989 Hurco Km3P retrofit

    Hi,

    I have a Hurco KM3P with some errors on the Z axis. I suspect it's the Personality Board, but i'm not sure. The machine is running ok, but when i run a drilling program, as soon as the drill...
  14. Replies
    16
    Views
    9,307

    Well, i'm here again, after all of these years......

    Well, i'm here again, after all of these years...

    Thing is that i stopped working for this company for a while and now i'm back for good and the machine is still not working. They bought the...
  15. Hi there again! It's been a while since i had...

    Hi there again!

    It's been a while since i had those problems with my machine, but, happily, i managed to fix it back then. Now i have a different problem.

    Because of some chips, one of the...
  16. Replies
    22
    Views
    3,253

    Hey guys, i still haven't figured this out. Still...

    Hey guys, i still haven't figured this out. Still waiting for some of your help, here :drowning: Thanks a lot!

    Greg
  17. Replies
    25
    Views
    7,183

    I'm back with new informations (problems...

    I'm back with new informations (problems :tired:).

    I don't know if the motor was stuck while the power was on or off, i just know i couldn't home the machine because the motor on the Z axis...
  18. Replies
    22
    Views
    3,253

    So, i'm back with some new info. I had to take a...

    So, i'm back with some new info. I had to take a break because i've been reasigned for the last few weeks.

    I did some tests on the machine and this is what i found out:

    The machine is working...
  19. Replies
    22
    Views
    3,253

    I just ordered some new brushes, but i don't...

    I just ordered some new brushes, but i don't think that's the problem, because i swapped the motors and it's still not working. The problem is still on the Z axis, even after swapping the motors.
    ...
  20. Replies
    25
    Views
    7,183

    Bridgeport Series 2 Interact 2

    I still haven't fixed my machine. I hit a dead end trying to find the problem and i just left it and worked on something else (for a few years :tired: ) . Now i need to use the machine. So, i have to...
  21. Replies
    22
    Views
    3,253

    Hurco KM3P Problems

    Hi. I own a KM3P Milling machine and i've been trying to fix some problems for the last two years, i think. The machine used to work fine, until one day i got the overload message on Z axis. I was...
  22. Replies
    16
    Views
    9,307

    Gildemeister CNC Lathe NEF CT 40

    It seems like Gildemeister lathes are not that easy to fix, because no one gives helpful advices. Even DMG Romania are not helping with anything, so i have to try fix it by myself, without any wiring...
  23. Thread: Hurco KM-3P

    by gugu
    Replies
    5
    Views
    1,448

    HURCO KM-3P

    Hello. I own a Hurco KM-3P Milling machine and i've been having problems with the Z axis. If i try to run a drilling program, when the tool touches the surface of the part, the Z axis stops and i get...
  24. Replies
    25
    Views
    7,183

    So...the latest updates... First of all, i bought...

    So...the latest updates... First of all, i bought this machine a few years ago, but i didn't use it, because i had the chance to buy a Hurco Milling Machine and i used it instead, being easier to...
  25. Replies
    25
    Views
    7,183

    Bridgeport Series 2 Interact 2 problems!

    Hi everyone!
    I'm having some problems with my Bridgeport Series 2 Interact 2... When i tried to home the machine, after the X and Y axes were homed, the Z axis didn't move at all, so i opened...
  26. Replies
    25
    Views
    7,183

    Hi everyone! I'm having some problems with...

    Hi everyone!
    I'm having some problems with my Bridgeport Series 2 Interact 2... When i tried to home the machine, after the X and Y axes were homed, the Z axis didn't move at all, so i opened...
  27. Replies
    25
    Views
    7,183

    Hi. I need the electric schematics for Bridgeport...

    Hi. I need the electric schematics for Bridgeport Series II Interact 2. Do you know where i can find them? Thank you.
  28. Replies
    16
    Views
    9,307

    Gildemeister NEF CT 40

    I talked with Gildemeister Romania, but they said they had and argue with Gildemeister Germany and asked me to wait until they fix their issues...

    I changed plate nr 2 with another plate from...
  29. Replies
    16
    Views
    9,307

    Gildemeister NEF CT 40

    Hello!
    I own a Gildemeister NEF CT 40 Lathe and i think i have some problems with the CNC board. When i turn on the machine, i get these messages:

    DISPLAY AND GRAPHIC INTERFACE......0.064.110....
  30. Replies
    15
    Views
    1,787

    Hello again. I managed to fix the old problem...

    Hello again. I managed to fix the old problem with the Churchill lathe, but now i have another problem. The lathe worked fine for a few months now, but today, one of my colegues didn't pay much...
Results 1 to 30 of 48
Page 1 of 2 1 2