Fixed we had to reload firmware.
Type: Posts; User: gguidi
Fixed we had to reload firmware.
Thanks, I got it figured out with some help.
Is there a way to rotate screen? Now x is let to right and y is top to bottom. I would like the opposite. Thanks
I just purchased this machine and it was working from the keypad well. I downloaded pss motion program and established communications with it. I tried to send a gcode file and now it is stuck on...
Thank you that will help.
I just acquires an a SF machine can anyone point me in the right direction for a user manual?
Thanks in advance.
Gary
Simple drilling machine with 4 air valves and a few limits. Could be by the hour or by the project.
Hi,
I am building a 5x10’ CNC laser. I have two Copley XCE drives and Servo motors. Could any recommend a motion controller that will work with these drives and Mach3? Would ecat be best from the...
I have a R2E3 with a boss 8 control. The spindle makes a lot of noise is this normal. It gets warm but not hot.
I have a bad Mitsubishi TR-6DA1 monitor on my cnc machine. If anyone has or can point me in the right direction for a scmatic please let me know. Or how to interface a video monitor.
Gary
Does anyone have a god source for low cost ACME Delrin nuts. Looking for a more cos efective source that Roton. I may need 100 pcs.
Thanks
Gary
I have decided to sell this cutter I have never used it. Anyone intersted please let me know.
Gary
Hi,
I have the same machine. I had a phase converter set up and I had the same problems. I added a variable frequency ac drive to run the spindle and am running the drives and the logic on 220...
Charge by the time it takes to cut the job. Decide on a rate per hour that will cover your costs and time.
Gary Guidi
www.depronlasercutting.com
If the chinese company that you purchased you laser had a US service center that stocked parts and could troubleshoot problems at board level what would it be worth to you in the price of the laser. ...
I just finished my cnc foam cutter. Photos can be found at this linkhttp://www.depronlasercutting.com/foam.html
I am running CeNeCe cutting at about 20
Gary Guidi
Depron Laser Cutting
Eb,
It is "0" It might be loosing steps but the error is so repeatable. If I block cut it returns to the correct "0" position. I am running 400 steps per rev with a 16tpi screw.
I am...
Hi, All
I just finished my cnc foam cutter and have it running on foamworks
well. I am deciding what software to purchase and am now trying GMFC.
I have it running but after it makes a cut it...
My R2E3 would only stat once in a while. It turned out the the incoming voltage was to high. You may want to see if it is taped right.
Dose anyone know how tight the wire should be in pounds of pull. I am designing a wire tension system and need to know where to start.
Thanks
Gary
Depron Laser Cutting...
Hi, All
I just purchased a Bridgeport with a boss 8 control. I drew a simple rectangle with a .5 radius on the corners. I am using right tool comp. I get two corners that cut correctly. 1 corner...
What is the best way to do this. I understand the sprial/pipe option. It is ok but is there any way to have it pick the center of the hole and have it start there? Rather than finding the center and...
Could someone email a Onecnc post for a Bridgeport with a boss8 control or point me in the right direction.
Thanks
Gary Guidi
[email protected]
Hi,
I am in Ashland MA I need someone to teach me a little about running a r2e3 Bridgeport with a Boss 8 control. Bobcad help would be great also. I have a CNC laser that I cut foam on so I do...
I need to move one this week. Dose it have holes to lift with?
Thanks Gary
When I get files from some of my customers in DXF format I open them in Auctocad. On the arcs I have hundreds of points. When I bring the file into Mach 3 it takes forever and the gcode file is huge...