Anyone??:wave:
Type: Posts; User: toranacar
Anyone??:wave:
Hi guys
I'm in need of help regarding this controller Siemens 808D Lathe.
So, i have created a CAD model on Mastercam 2017 but have Generic, HAAS, Fanuc and couple other machines listed in my...
Hi, Im very interested in using drip feed on my Fanuc OM mill. I have a 1992 Leadwel MCV OP.
Has anybody used a DNC Titan device??
Thanks, just trying to confirm this is correct before i make...
Thank you, all good i finally worked it out:)
This is really interesting, I have a 1992 Leadwell MCV OP. Fanuc OM. It doesn't have tape mode switch, i will see if this works for me. I want to buy DNC Titan device for drip feed. Anyone use this?
Just tried M19 and spindle is not turning/orientating but I can hear the relays switching. I remember when I had a technician looking at this he did mention this issue.
Also the technician made some...
Just found this, ill try it in a moment.
M19 spindle orientation.,
https://www.helmancnc.com/fanuc-m-code-list/
So whats happened so far.
M26 tool unclamp OK
M25 tool clamp OK
M24 Mag down OK
M23 Mag up OK
M21 Mag right Error 1036 T number unmatched and 1042 SPDL Unorient
M22 Mag left didn't work as...
Hi machinehop5
I'm back to this issue again which I never resolved, ATC. I've got other parts of the machine working and actually made a part, I'm using this as a single tool at the moment.
Ill...
Thank you. Thats a good point.
The thing about contour mill (And this is probably a setting issue) is when I have used it, it wants to cut 0.1mm at a time which makes the program super...
Hi guys.
Just wondering how to leave 4 tabs for example on all 4 sides of a square or rectangular profile? Tabs being 5mm wide.
I'm trying to cut out the center of the square without it moving...
Ok cool.
I just realized i can use slot mill in 2D with 0 overstep:D
Hi Guys
Basically, milling a rectangle (test) 1mm deep (so basically 2 cuts) (250mmX145mm) at 0.5mm increments using dynamic contour milling in 2D.
This should be a short straight forward G code...
Thanks mate, yes I hope to put this machine to work soon.
The other issue I see is the program number is in reverse when I transfer the program but that's something ill deal with another time, I...
You guys are fantastic! Thanks guys/gentle giant.
I did exactly P cancel. the limit switch needed adjusting as it wasn't fully pushed in so it over travelled. Adjusted switch, moved table off the...
Thank you, Ill try soon.
P button and Can beside it.
489004
Thanks mate :D
Thank you for that.
This machine does have batteries, as far as I've been told it is to back up the "parameters" memory.
I haven't removed the belt or motor which is directly mounted to the ball...
Hi guy's
I finally assembled most of the CNC, replaced rails and linear bearings, the machine is much quieter.
I believe i screwed up the X axis home. So, trying to back track what i have done, i...
sorry guys wrong thread. Ignore that
Hi guy's
I finally assembled most of the CNC, replaced rails and linear bearings, the machine is much quieter.
I believe i screwed up the X axis home. So, trying to back track what i have done, i...
Cool, thanks. Thats what the supplier said today also.
He did mention the arrows on the rail and bearing should be pointing same direction which makes sense.
Hey guys, I can't actually find an M for master on the rails
I think ill end up getting a technician in to do it for me, that's what Im thinking anyway but so close to Christmas it will be in the...
Yes the rails have an edge on the CNC chassis to butt against
Hi guys
I finally examined the rails and bearing and noticed they have arrows on them. I'm guessing these arrows should point towards the chassis edge?
487340
487342
Thank you, ill read over again what you guys wrote. Got to go, thanks guys
Oh there's a mark, i didn't know that, still learning i guess :D
Thank you mate. :D
0,045mm = 0.00177165"
Hi guys, Im just measuring the parallel on my rails and im getting 0.045mm from one end of the rails to the other. I dont have the manual which tells me if this is outside machines specification....
Hi guys, just wondering what the torque settings would be for the rail bolts?
Are the torque settings critical or should they just be tight?
Thanks
Bart