Thanks Bubba, just trying to get a feel for what other operators are doing.
Type: Posts; User: curlyweld
Thanks Bubba, just trying to get a feel for what other operators are doing.
I am running windows xp on my ez router plasma cutter with mach 3, and i have windows xp on the office computer where i make my drawing files and do my interneting. Now that their dropping support...
Use a tester and check for continuity between the red wire going into the gecko drive and any good ground. If you have continuity then it could be fried. I had two burn out from lighting storm and...
Hey Zac or anybody that can help. I have one of ez routers combo package,plasma and router. I have been plasma cutting for four years now and have never needed to set up the router. Now I have a...
Have any of you ez router guys bought the plasma router combo, I did and have not tried the routing yet. I would like to know what all is involved in swithching over. I would like to know what kind...
Can someone help me, I have a 3.5 year old Hypertherm 1000 with a machine torch. Awhile back the torch safty switch would not work, it stayed in the open mode and no red light when consumables...
I have a three year old Hypertherm 1000 and have been very happy with it. I am now thinking of upgrading to the new Duramax retrofit torch. I'm wondering if anyone else has done this upgrade and if...
Thanks Jim, that all makes sense,I think my biggest mistake was the motion delay. I will try your recommendations and practice a little more on half inch until the 9/16 plate gets here. Also I will...
Also forgot to mention my arc volts are at 144 and motion delay at 1. Now that I look at the chart I see they recommend 1.5, might be a good place to start. What do you think?? THANKS,,,,,,,CURLY
Hey Jim, Curly from CURLY'S WELDING, I have a 3 year old power max 1000 (great machine,no problems) on a 5 by 10 ez router table. I have cut half inch with little or no problems. I tried 5/8 once but...
If you think it's just dragging when moving from cut to cut then you need to set you travel height in sheet cam. I set mine at 1.5 inches and has always been high enough to clear small tip ups. I...
I bought some of the last plasma quench and it worked well,then you could not get it anymore. I found this place two years ago and have been happy with what they sell me. It seems to work just like...
Not trying to highjack anybodys thread,but this was the latest one on quench. Just wanted to let everybody know about Pico Chemicals, they have a product called Pico quench guard. I started out with...
KEEP CALLING TILL THEY MAKE IT RIGHT!!! I bought from EZ and a few problems also. Maybe 50 % of the time when you called you could get someone to help. It did all pan out and have been running my...
Thanks for the quick reply, I figured it had to be something simple. While I got your attention could you tell me if it pays to turn off the plasma cutter everytime I'm not using it? How much juice...
I have a ez route plasma with THC for two years now,no problems other than my own. The otherday I had to cut some 24 gauge galv and decided to use my fine cut tip. I switched to the deflector...
I have two side rails with rack and drive gears that came off from a ez router 5 by 5 table. I converted my table to a 5 by 10 and have these left over. I've been meaning to put them on ebay but...
Parm, I don't know about cut 2d but corel draw with the dxf tool is a lot eaiser the the bobcad program I was trying to operate with,that also was the cad program that came from ez.I learned most of...
PARM, Just wondering how you are getting along with your machine? I have a ez 5by 10 and have had good luck with it. I have another friend that has your same machine and has had no problems that I...
Thanks Jim for the heads up on the switch,today I took the torch body apart and just like you said it was built up with what looked mostly like lime.Cleaned it all with small wire brush and back to...
Millman,if it's just those two sizes,one circle and one square can't you load one of each into sheetcam and then nest them by hand into your size of material??Just my two cents,good luck,,,,CURLY
MILLMAN,about your post of bc,I had a new Bobcad salesman call me the otherday with their new software that would import artwork and do many other great things.It sounded like all the things I do...
One other thing after reading your post again.Yes thc needs to be on and the correct tip volts set using charts in your plasma cutter book.If you have no chart I would suggest starting at 145 volts...
I also started with bc,I even bought the learning cds,what a waste of money.The best thing I did buy was corel draw x3,the next well spent money was corel draw add on tool.To this day I only use bc...
JIM ,Thanks for quick reply, I forgot to tell you that I have a machine torch.I looked through the manual (kind of fast) and did not see a exploded view.At least nowi I will treat it with more...
This question is for Jim Colt. Jim I've been cutting two years now with hyp 1000.Whenever I would change tip consumables I would get a red lite on the machine.I assume it was from removing the...
Ordered two new complete 10 foot rails,gear racks,guides,gears and belts for my 5 by 5 ez route plasma table. This is going to be a winter project.First I'm rounding up all the parts,then remove...
Hey thanks ANDY,I went on ebay and got everything I needed for about 35 bucks and should do about 400 gallons. thanks again,,,,,,,,,CURLY
Has anybody ordered plasma quench from KOAL INDUSTRIES recently.I ordered from them about 1.5 years ago and had good luck with their service.Not long after that I started to read about poor service...
TIM, just to let you know I also had to call back about my sheetcam license and having the wrong cables. The license was taken care of very quickly,when I got to the box that had all the cables in I...