Ok I will reinstall Mach3 and your screenset
if it dose not work I will send you a video.
thanks for the Help
Type: Posts; User: goranmax
Ok I will reinstall Mach3 and your screenset
if it dose not work I will send you a video.
thanks for the Help
just about 30mm
when T3 calls.....my Z Axis is higher.
I have already changed this
"In the M881, M889, and M6End macros, you need to change the value of FirstProbeDist.
There are two, one for inches (6) and...
Well I have copied all macro to the right folder out the the 2010 folder.
and I do not have the Ignore M6 calls checked.
Yesterday I tried to leave the M6 in the G-code.
What happens.
doing...
No one????
HI
yes I did...but than it stats right to mill again.
No Probing for the second tool length....just stays low at +-o on the Z axis.
Hi
Breakout board over parallel port connected to
Windows 7 32 bit.
Mach3 .43.62.
only message press cycle start after tool change.
Stop Spindle, Wait for Cycle Start is activated
HI Gerry
here it is the link with the M6 still in the file
smal_clock_30mm.nc :: Free File Hosting - File Dropper: File Host for Mp3, Videos, Music, Documents.
Hi Gerry
don't understand what you mean.
When I do not delete the first M6 from the G-Code....the machine will not probe and will not go to the reference plate for the second tool.
It just stays...
Hi
Seems to work now. Just had to remove the first
M6 in the GCode and the TC works.
Cheers
Hello all
does someone use the metric 2010 screenset for Mach3 with Initial Auto Zero Macro for Tool Changes for MeshCam?
with my G-Code its not working.
when the first Tool is finished...the...
Hi all.
hope some one can help me.
who has a Metric Post Processor for Gerrys 2010 screenset?
I know there is one for Vectric Aspire.
But I don't get the application ...it's really bad for...
Hi Gerry
Do you might have other post procesors for other aplications ??
like for vetric Aspire. For exporting the gcode correctly?
I think that aspire is really bad specially when importing...
Hi Gerry
Thank for you help.
Good that the probing works now.
But now I have a question after the probing when the G-Code is loaded .....the probing starts again...
at the point after...
HI Gerry
I got it to work now.
No Noise issue...it was related to my computer that I used .
I just took a different computer with all the same Mach3 settings and it works now.
But...
Hi Ger. ... sorry for my bad English.
I tried Mach3 version 3.043.062 over parallel port...
and all seemd OK when touching the touch plate in my hand seemed to work
Mach3 recognized the plate...
Hi
My Mach3 is set to mm configured it from the start in units....set steps per unit.
I can also see it in the original mach3 screen under Settings tab.
when doing a set steps per unit test...
uuhhh I had the 3.043.066.
Well I have installed Mach3 older version : 3.042.020
but still same issue.
also with this version .....when probing........Z Axis is moving down...verry slow and...
Hallo Gerry.
Im using Mach3 Version R3.043 .
My CNC connected over Parallel Port to my breakout Board.
Touch Plate connected to pin 13.
In Mach3 page Diagnostics...I see the Digitize signal...
Hi
Thank you for info.
I have puchsed the 2010 screenset and give it a try,
thank you
Anyone???!
Hello all...
I hope some one can help me wit setting up my Touch plate in Mach3 /CNC machine.
I just started to build my machine and I cane across some strange problems setting up my Touch...
hallo all,
I hope you can help me.
I just purchased three Stepper Motors:
Motionking Typ 34 HS 0404-02
4 cables
1,8°
6.8 A x Pahse
3,0 Nm
thank you for the info.
the 115V was on the website that I saw.
but on the Moter it is 24V
sorry for that
Hi all
I hope you can help me.
I have 9 of those servo motors that I got really cheap.
I wanted to use the motors for a CNC machine that I'm building.
Can anyone tell me how strong the...