Same question almost 10 years on. Did you find any information?
Type: Posts; User: Sky Gazer
Same question almost 10 years on. Did you find any information?
Sorry if I posted in the wrong section - moderator please fell free to shift to most appropriate forum
Can anyone tell me where I might be able to source the HAAS style AAG cylinder and MQL...
Update that might hopefully help some one else who might find themselves in a similar situation.
I was reluctant to use a hydraulic press when I was unsure of the components and did not have an...
Hi Guys,
I have a Fimec ES929 HSK 63 spindle with less than 100 hours use which I allowed to bottom out on some MDF for a couple of minutes.
When I removed the slightly discoloured tool holder...
Yes my first problem is getting the gripper to release
Hi Guys,
I have a Fimec ES929 HSK 63 spindle with less than 100 hours use which I allowed to bottom out on some MDF for a couple of minutes.
When I removed the slightly discoloured tool holder...
I am not aware of any Biesse/HSD agent in Australia.
Not to worry I will work it all out eventually- It just would have been so much easier if FIMEC had provided useful customer support to...
I purchased from Fimec in Italy - I doubt they have an Australian Agent .- and had to split the shipment in two with the inverter leaving Late in August before they went on holidays for a month and...
QUOTE=sfl2012;1070201]Did you get manuals with your products? Fimec and HSD are really identical products... The prewired cable should have a coding sheet... Hope you can figure it out.[/QUOTE]
...
Hi ,
Did you manage to get your Fimec spindle to run.
Did you purchase their inverter too?
I purchased both but have had no successs whatso ever in getting them to help me wire up the...
No worries there they don't have any support with a cracker - I bought an ES929 as well as their cable and recommended inverter back in August of last year and went to install the components in late...
Any news on this front?
I too am looking at a ATC system and considering Colombo 10 HP unit but have been quoted over 10K for the unit alone . After reading this thread I tried to have a look at the Fimec site but didn't...
I was lucky enough to have a small mini router system on hand that I also control with Desk CNC so it was easy for me to just swap the USB input cable over and see if the same erratic behaviour was...
Hi electronicos,
The answer to my problem after replacing just about all the components was rather basic infact. The crimped bootlace terminals that were wired into the driver were actually of...
Hi Bob,
Thanks for the heads up with the link it was most informative.
I emailed Trans Con to see what the adaptor kit for HSK was all about and am waiting on a response.
Alternately new...
Hi ,
I have a 100 mm 350V 5.5 kw? liquid cooled spindle running an ER 20 Collet system.
I am getting a little impatient with changing the collets and woud like to go for an upgrade or even an...
Thanks Signmaker,
The detergent and water sounds like a great idea to keep the process running freely. I will difinitely give it a try. What speed have do you recommend for 3 and 6 mm single...
Hi All,
I am not sure if this is the best place to post but I am looking to upgrade from my current 380 V 100 mm 5.5 Kw spindle to add ATC capability so I am guessing I am looking for a similar...
So Signmaker , can you give me your "heads up" on what will be the best tool,speed,feed and cut depth to cut 15mm Cast acrylic . I am looking to make a dust boot and don't really want to waste too...
Have a look at this page and you will see the grades I am talking about with their relative machinability?
http://www.aircraftspruce.com/catalog/mepages/aluminfo.php
So what grade of Aluminium are you machining?
I have just encountered an issue for a second time that is stating to concern me. When I initiate an up or down movement of the Z axis I find it is proving faulty - One second it goes in one...
Gary,
I think I have the little brother to your machine :) my JCut 1836 was manufactured and shipped in late Sept.
I decided to cut up the Vacuum tank and pump to relocate them in the vacant...
Beerman,
I would have to agree with you on that one.
What cnclaser is missing is that I am not about to waste any more time on this lame duck . I never really expected to use any of the...
Hi Beerman,
Yeah I would have to agree with you.
What cnclaser seems to be missing is that I have already given up on there back up service- I was dismissed pretty promptly and am not about...
As I believe said a couple of time I DID email your sales -NO SUCCESS- How many times do I need to do so.
As you said a big machine - not a small sale
I purchased the JCut 1836 with a 500 mm Z axis
I did contact Lily and reported the problem but that was as far as the interest went - of course - I have already paid for it.
Is there a set of instructions in English on the Discs with Chinese...
I didn't say that either- I won't know if it is OK or not until I saefly power it up and get it running.
No there were NO english instructions and my pointing this out last week apparently fell on...