584,837 active members*
5,251 visitors online*
Register for free
Login

Search:

Type: Posts; User: nautomation

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,788

    the problem is it that you have to assign the...

    the problem is it that you have to assign the macros for as per ladder or to co relate with Ladder
  2. Replies
    7
    Views
    4,914

    you have to enter the parameters from IPL Mode...

    you have to enter the parameters from IPL Mode the 9000 Series rest after in normal mode
  3. Replies
    2
    Views
    1,681

    Please inform the drive and motor number

    Please inform the drive and motor number
  4. Replies
    9
    Views
    1,096

    Check that you have 100vac between terminals 3...

    Check that you have 100vac between terminals 3 and 4.
    If you do, see if both contactors on the drives try to pull in.
    If both contactors pull in and drop out again, pull the main fuses and...
  5. Replies
    2
    Views
    1,298

    it seems that servo are not initialized, or power...

    it seems that servo are not initialized, or power up. Please check the servo power
  6. Replies
    1
    Views
    118

    Hi Expert , Please check the spelling of...

    Hi Expert , Please check the spelling of Electronics , parameters , and Contact in your post .. also please let me know I have some problems in Look ahead blocks in fanuc 3 , can you solve it ?
  7. First you remove the motor from gear box run it...

    First you remove the motor from gear box run it outside , try to rotate the spindle shaft by hand and see is it free or jammed /. the spindle motor bearing change is not a big task , but you have to...
  8. Replies
    2
    Views
    761

    please attach your wiring diagram to understand...

    please attach your wiring diagram to understand better what you did ,..
  9. This is an external alarm due to turret not...

    This is an external alarm due to turret not clamped and baar feeder is not in position may be the cause or failure of hydraulic pressure . interlocks and limit/proximity , see in ladder for details .
  10. Replies
    4
    Views
    9,955

    see in ladder or reload the PLC data , such as...

    see in ladder or reload the PLC data , such as PARAM < DGNOS
  11. Check the clamping , Hydraulic pressure and any...

    Check the clamping , Hydraulic pressure and any interlock
  12. Replies
    1
    Views
    3,317

    The EPROM OE1 and OE2 may be faulty.. or the...

    The EPROM OE1 and OE2 may be faulty.. or the board base ..
  13. Replies
    4
    Views
    2,483

    what is the series of fanuc control you are using...

    what is the series of fanuc control you are using ?
  14. is the pulsecoder fitted with coupling ?

    is the pulsecoder fitted with coupling ?
  15. Replies
    5
    Views
    2,735

    yes the machine can with a third party software

    yes the machine can with a third party software
  16. Replies
    2
    Views
    1,651

    check the x axis servo pulsecoder and motor

    check the x axis servo pulsecoder and motor
  17. Replies
    1
    Views
    413

    The LED are Alarm LED

    The LED are Alarm LED
  18. Replies
    6
    Views
    682

    put a dial and see the all axis in respect to...

    put a dial and see the all axis in respect to spindle , and confirm for specific comment on troubleshooting
  19. Replies
    1
    Views
    3,964

    PARAM_INFO BIT_NO DESCRIPTN KEY PARAM 000 1...

    PARAM_INFO BIT_NO DESCRIPTN KEY
    PARAM 000 1 T/M CIRC. INTER BY RAD.
    PARAM 000 2 T/M ADD 16 OFFSETS MEMORY
    PARAM 000 4 T/M CSS B (ANOLOG OUTPUT)
    PARAM 000 5 T/M G20/G21 SWITCHING (INCH/METRIC) ...
  20. fidia controllers are good , but compare to...

    fidia controllers are good , but compare to heidenhain it is not perfect
  21. Dear Sir What is the CNC control ? you have to...

    Dear Sir
    What is the CNC control ? you have to check the Level Switch of Lube Pump it is in NC or not ? Next , If you can tell the exact CNC control Model , Than Troubleshooting will be better as i...
  22. Check if there any interlock in manual mode ?

    Check if there any interlock in manual mode ?
  23. Replies
    10
    Views
    5,258

    Check The Turret clamp , The Air Pressure Switch...

    Check The Turret clamp , The Air Pressure Switch and Door interlock it is an External Alarm
  24. Replies
    2
    Views
    725

    It is a problem related with odd and even parity...

    It is a problem related with odd and even parity , remove the cards again and Fix in the Slots Check the Slots pin and Connectors Properly , There is no chance that The Ladder will be Deleted...
  25. Replies
    4
    Views
    1,007

    The 401 stands for X axis , check the X axis...

    The 401 stands for X axis , check the X axis drive PCB and Voltage also check the parameters of x axis
  26. Corrective Action l Check the position of the...

    Corrective Action
    l Check the position of the RUN/STOP key switch, See step (1).
    l Check the condition of other status lights (PARITY, BATTERY, CHAIN OK, CHECK
    and POWER).
    l If no other problem...
  27. RUN Light on Or Off ? If off than CPU is in stop...

    RUN Light on Or Off ? If off than CPU is in stop mode. and what about the CHECK Lit it is on or OFF ? If the Run Light is off The major cause is = CPU self-test has not passed within 300 ms *50 ms,...
  28. The PLC went in STOP Mode , Check the PLC Data ,...

    The PLC went in STOP Mode , Check the PLC Data , Reset the PLC ,
  29. Replies
    1
    Views
    1,030

    See the Mother board Box , Interface cable to...

    See the Mother board Box , Interface cable to Display , Only Display not works ? after Power on Rest buttons LED Lit or not ?
  30. Replies
    8
    Views
    7,498

    Dear Sir , Check the Control 24 V Circuit for...

    Dear Sir ,
    Check the Control 24 V Circuit for your MOP(Machine Operator panel ), Next as you told that operators will thump the cabinet with a dead blow after that machine power up , Seems there is...
Results 1 to 30 of 134
Page 1 of 5 1 2 3 4