584,846 active members*
4,361 visitors online*
Register for free
Login

Search:

Type: Posts; User: magzi

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    593

    Syntec 900me data.

    My Syntec 900me controller has a dead motherboard.
    I manage to find a second hand one and I am trying to reinstall its software.
    I have a backup of the original controller.
    Does anybody know where...
  2. Replies
    10
    Views
    2,934

    Re: Syntec VMC 1060 password

    Can anybody share a Syntec 900me internal CF data?

    Thanks in advance

    Michael
  3. Replies
    14
    Views
    3,530

    Re: SYNTEC 900ME parameters password

    Dear geast1967,

    Does your machine have a CF card inside the controller? (on the advantech's PCA6773 motherboard?)

    Best regards
    Michael
  4. Replies
    4
    Views
    742

    Re: Quick-tech VMC1060 with SYNTEC 900ME

    Finally I found out that the PCA6773 itself is the problem.
    It beeps when booting but no VGA output.
    Any thoughts?
  5. Replies
    4
    Views
    742

    Re: Quick-tech VMC1060 with SYNTEC 900ME

    Do you know which is the memory chip?
  6. Replies
    4
    Views
    742

    Quick-tech VMC1060 with SYNTEC 900ME

    Hi there,

    This machine used to be sold in Europe and especially in Sweden.
    I'm wondering if anyone else who has the same machine, knows if the operatting system runs from the CF card installed...
  7. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    set parameter 9934.4 to 1 (=enable JD5B)
    i/o channel to 2
  8. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    I have found the blown ICs and diodes in order to repair the damage.
    Also changed to serial port 2 and now it is working.
    Thank you all
  9. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    I have already tried this, but LSK doesnt flash when start receiving.(btw, I use @122 as device type 0.Is it right?)
  10. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    I have the same IP to Rs232 MOXA that I use on a lathe. I tried it but still with no luck.

    Is it possible to find a schematic of the board A16B-3200-21 9/02A because as I keep searching, I have...
  11. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    I have the pinout. The cable is good, it use to work for me.
  12. Replies
    14
    Views
    1,930

    Re: fanuc 18mc serial port dead

    the problem is in the control or cable.
    I try to use serial port 2 (channel 2) changing the serial cable to JD5B from JD5A but with no luck, even LSK doesnt flash.
  13. Replies
    14
    Views
    1,930

    fanuc 18mc serial port dead

    I have a Supermax mill with fa anuc 18m control.
    The machine was in a good working condition. Today I discovered that the Pc attached on its serial port does't boot any more.
    After some searching I...
  14. Thread: SVC-A board

    by magzi
    Replies
    1
    Views
    575

    SVC-A board

    Hello,

    My LS30N keeps damaging every SVC-A board I try (3 in total) after some time.
    I have even replaced complete the drive together with SVC-A board (E4809-770-015-D).
    Can I replace SVC-A...
  15. Replies
    29
    Views
    5,368

    I checked the pulse coder cable, OK. I added a...

    I checked the pulse coder cable, OK.
    I added a cable to ground from the replaced MZ sensor (the machine originaly had a M sensor in the spindle motor).
    This way the alarm hasn't appeared yet. ...
  16. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    419498

    this is my mainboard.
    Couldn't reply to your PM. Your storage is full.

    Goodmorning
    Michael
  17. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    Do you know how to change the mainboard?
    I think I don't have option2.
  18. Replies
    29
    Views
    5,368

    Only 2003 X crc=1 and stb=1, all others are 0....

    Only 2003 X crc=1 and stb=1, all others are 0.
    This morning I tried some g84 cycles and alarm 351 continuous and also #200 x dca=1
  19. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    I found out that the previous owner had replaced the spindle motor and this one has inside a MZ sensor although the old one had a M sensor, because the plans I have state this.
    I checked the cable...
  20. Replies
    29
    Views
    5,368

    I will check it tomorrow. Thanks for the help. ...

    I will check it tomorrow.
    Thanks for the help.
    Michael
  21. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    Every time, but the time the alarm follows it varies from 2 sec to 10 sec.
    I found that my machine has a M sensor and a position coder because there are cables connected to JY2 and JY4 ports of the...
  22. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    I have started from the begining to find maybe a pattern of what happens to trigger the alarm.
    This morning I referenced the machine then issued a M19 spindel orientation into MDI mode and all the...
  23. Replies
    29
    Views
    5,368

    The alarm is happening always with the x axis...

    The alarm is happening always with the x axis stopped. I have tried to move the cable from both ends in case any of its wires is loose although I checked its wiring and ground.
  24. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    The toolchange is happening exactly as you mention exept it has not a pneumatic cylinder but a 3phase motor.

    When the alarm is generated during the toolchange macro, it doesn't happen on a...
  25. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    The machine is grounded.
    Everithing is happening when no other equipment is on at the factory.
    The strange thing is that 90% of the circumstances, the alarm is happening during or afterwards a...
  26. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    No, just where the program is interrupted, X and Y stop at whatever point they are,M06 is executed and then the program continues (if the error doesn't happen)
    The error would be happen anytime...
  27. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    I swap servo module a20b-2902-00700 of 1/2 axis with the same module of 3/4 axis.Problem still the same and most of the cases when in or after a while of a toolchange cycle?
    The manual suggests when...
  28. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    I have a 3 axis card.Which cables should I swap? Cables to motor, encoder and control cables?
  29. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    I have tried ferrites but nothing changes.
    The fact that after I do a cable swap between X and Y axis and still the error is 351 x-axis alarm and not 351 y-axis alarm,I think it is not the servo...
  30. Replies
    29
    Views
    5,368

    Re: fanuc 18m 351 alarm

    Is it possible to have the problem due to a broken spark killer or diode, because most of the times, the alarm is happening during M06 cycle?
    Has anyone met anything similar?

    Thanks
    Michael
Results 1 to 30 of 46
Page 1 of 2 1 2