584,866 active members*
4,986 visitors online*
Register for free
Login

Search:

Type: Posts; User: pjeran

Search: Search took 0.00 seconds.

  1. Replies
    1,242
    Views
    77,971

    Connectors

    This is a great thread!

    Interesting that the discussion is getting around to connectors. I just finished prototyping some using a 2.5mm microphone plug. They are nice and compact. The one thing...
  2. Replies
    47
    Views
    12,059

    George, First thanks for all your help in the...

    George,

    First thanks for all your help in the forum.

    You have mentioned a set of KTK service notes about 6mb in size. I have the KTK drive that is running right now, but would like to be...
  3. Replies
    1,343
    Views
    42,753

    Steve - thanks for the help. That was the...

    Steve - thanks for the help. That was the winner, spinning smoothly now.

    For some reason I thought the base freq was the lowest, guess not...

    Now I just have to finish the rest of the CNC!
    ...
  4. Replies
    1,343
    Views
    42,753

    A little help for a Hitachi X200

    It is after hours so I thought I would give the zone a shot.

    I am trying to get my 2.2Kw spindle up and running with a Hitachi X200.

    I have adjusted the following parameters:
    A003 - Base...
  5. Replies
    2
    Views
    647

    George, Thanks for the help. pjeran at...

    George,

    Thanks for the help.

    pjeran at cableone dot net will work

    if that does not work I can PM you another address that can handle the 20MB file.
  6. Replies
    2
    Views
    647

    Problem with a KTK drive

    I am having an issue with the KTK drive on my Bridgeport Interact 1 Mk 2. From a cold start, the program will start up the spindle and run the job just fine, but when the spindle stops for a tool...
  7. Replies
    4
    Views
    1,092

    This is similar to a message that I just resolved...

    This is similar to a message that I just resolved on my Mk 2. In my case, after swapping the motors and cleaning all the external contacts throughout the encoder path, I went inside the controller...
  8. Replies
    11
    Views
    3,130

    Just thought I would post a follow up for anyone...

    Just thought I would post a follow up for anyone else that might run into this problem.

    It has taken a while, but I traced and reseated every connector in the encoder path, swapped servo/encoders...
  9. Replies
    11
    Views
    3,130

    Thanks George I will give them a call.

    Thanks George I will give them a call.
  10. Replies
    11
    Views
    3,130

    Gus, When I swapped the servo I swapped the...

    Gus,

    When I swapped the servo I swapped the cable too. I am now wondering if it is something in the 155 control. At a loss right now.

    A while back I lost all the parameters due to the battery...
  11. Replies
    11
    Views
    3,130

    George, Finally got a chance to swap the...

    George,

    Finally got a chance to swap the servos, Z for X. Unfortunately, it did not follow the servo, still getting the Z measuring system defective A error. The X axis worked fine.

    I have...
  12. Replies
    11
    Views
    3,130

    George, Thanks for the quick follow-up. It...

    George,

    Thanks for the quick follow-up.

    It will happen using either the joystick or the hand wheel. It does not happen immediately, the first time it happened, I had been able to touch off on...
  13. Replies
    11
    Views
    3,130

    Z Measuring System Defective A

    Got a new error message that I can't find in the manuals that I have.

    I am running an Interact 1 Mk 2 w/ a 151 control. Went to power up the machine, it cycled through the x,y,z axis OK, but when...
  14. Replies
    7
    Views
    2,455

    this may sound obvious, but did you program in a...

    this may sound obvious, but did you program in a speed to turn at?

    If I remember correctly, from the NC control TOOL CALL and give a spindle speed press cycle start and then enter M03 then cycle...
  15. Replies
    0
    Views
    1,276

    Another 8x12 mod - QCTP

    After tuning my lathe this was the first thing that I did. Not too difficult, but makes using the lathe soooooo much better.

    A breif description:

    1. AXA toolpost and a 9/16-18 4" long bolt
    ...
  16. Replies
    7
    Views
    2,325

    Nice Mod! I think that one goes on the todo list...

    Nice Mod! I think that one goes on the todo list after I get my QCTP mounted.
  17. Replies
    18
    Views
    4,483

    Dan, ...

    Dan,

    http://filebase.heidenhain.de/doku/oma_controls/dvd_oma_html/de/index/N1304B/N148A3/N14ACE/N14ACE.html

    Has the technical ref manual. That should have a list of all the parms and what...
  18. Thread: heidenhain help

    by pjeran
    Replies
    12
    Views
    2,745

    George, Could you send me a copy of the tech...

    George,

    Could you send me a copy of the tech note. Now that the mill is up and running it is time to get it connected.

    My e-mail is paul(dot)jeran(at)hp(dot)com

    Thanks,

    Paul
  19. Replies
    17
    Views
    3,789

    George, Just want to say thanks for your help...

    George,

    Just want to say thanks for your help on the spindle debugging. Ends up it was a combination of issues.

    1. Needed to clean some contacts on the TNC-151.
    2. Had L1 & L2 in the phase...
  20. Replies
    5
    Views
    1,896

    Thanks George

    Thanks George
  21. Replies
    5
    Views
    1,896

    George, Thanks for the help. It is my friends...

    George,

    Thanks for the help. It is my friends machine that has its parameter list gone. I have to figure out how to get the parameter list out of my machine. Unfortunately, neither machine had...
  22. Replies
    5
    Views
    1,896

    Get machine parameters from a TNC 151

    I have a friend with the same machine and controler as I, but it is asking for the machine parameters to be reloaded (in german no less). It is an Interact I mk 2 with a TNC 151 controler. I have...
  23. Replies
    17
    Views
    3,789

    George, Thanks for the help. I sent you an...

    George,

    Thanks for the help. I sent you an e-mail with my address. The LED does come on, but I am only measuring a motor field of 203V ac or 124 DC, if I read the maintenance manual correctly it...
  24. Replies
    17
    Views
    3,789

    Help with a Interact I mk 2

    I picked up an Interact I mk2 at auction a while back. The controller and servos powered up fine, but the spindle won't spin up.


    I have the maintenance manual and have gone through the...
Results 1 to 24 of 24