584,826 active members*
5,275 visitors online*
Register for free
Login

Search:

Type: Posts; User: FLjoyride

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Please send file to [email protected] as...

    Please send file to [email protected] as well. Thank you.
  2. Replies
    6
    Views
    4,954

    Try calling Rick with Heidenhain in USA, his...

    Try calling Rick with Heidenhain in USA, his number is 800-233-0388 or his mobile is 847-519-4858. It sounds like you're having memory problems, you should try to get original parameters put in, and...
  3. Interact 720 spindle drive parameters needed

    Hi all,

    I had to recently have the NVRAM and EEPROM chips replaced in my fanuc spindle drive, and I do not have an original copy of the parameters. I have heidenhain control and Fanuc drives,...
  4. A06B-6055-H106 Spindle Drive AL-02 shutting off`

    I have a fanuc A06B-6055-H106 spindle drive for a Bridgeport CNC. A few weeks ago I had some problems with it giving me an alarm 17. I reset the drive and put all of the parameters back and it...
  5. Replies
    2
    Views
    892

    Fanuc AC spindle drive

    Does anyone know the part numbers or where to find them for the maintenance manuals associated with fanuc AC drive A06B-6055-H106? I'm having trouble getting the correct ones. Thank you,
  6. Replies
    19
    Views
    8,132

    A06B-6055-H106

    I wasn't able to access any parameters until I put the jumper into test mode. Once I did that it would flash from 000000 to 111111, 222222, 333333, 444444, 555555, 666666, 777777, 888888, 999999,...
  7. Replies
    6
    Views
    1,256

    Make a tool change program, and change the tool...

    Make a tool change program, and change the tool numbers as you load:

    0 BEGIN PGM 1 INCH
    1 TOOL CALL 12 Z S 2000
    2 L R F M06
    3 STOP M25
    4 END PGM 1 INCH

    So if you want to insert tool #...
  8. Replies
    13
    Views
    6,161

    I upgraded my pc also, to windows 7 64 bit. The...

    I upgraded my pc also, to windows 7 64 bit. The motherboard didn't have a com port so I got a com port PCI card ($20) which has been working great. Just make sure to select the proper port in TNC...
  9. Replies
    3
    Views
    527

    Check your stops and/or shock absorbers for the...

    Check your stops and/or shock absorbers for the tool changer. What type of tool changer do you have? Not sure what you mean with the head rising, can you elaborate more? Are you talking about the...
  10. Replies
    2
    Views
    785

    Make sure your data transfer parameters are set...

    Make sure your data transfer parameters are set correctly, you can go to the heidenhain website and download the documentation explaining each parameter. Once you get it working again, download your...
  11. Replies
    2
    Views
    713

    What are the dimensions of that beam? What is...

    What are the dimensions of that beam? What is the tensile strength of the steel being used? Are there going to be any supports (piling in middle, gussets). What do you want the factof of safety to...
  12. Replies
    10
    Views
    1,254

    Wow that looks great.

    Wow that looks great.
  13. Replies
    10
    Views
    1,254

    OK, I'll just wait for it to go out completely I...

    OK, I'll just wait for it to go out completely I guess. Thanks for the replies :) I'll keep in mind the LCD option as well.
  14. Replies
    10
    Views
    1,254

    I guess the picture was too big the first try,...

    I guess the picture was too big the first try, here it is.
  15. Replies
    10
    Views
    1,254

    TNC screen / tube replacement

    Bridgeport Interact 720 VMC
    Heidenhain TNC 2500 control
    Fanuc drives (red cap motors)

    I think my screen is going out, it's been getting really bright on the right hand side when I first turn it...
  16. Replies
    4
    Views
    1,530

    I got two of these when my 24V power supplies...

    I got two of these when my 24V power supplies went out (TNC2500b), they are great for sensitive equipment and have less 'ripple' than the specs required by heidenhain. Don't cheap out on the power...
  17. Replies
    4
    Views
    1,530

    You should have two 24V power supplies in your...

    You should have two 24V power supplies in your electrical cabinet. Find them, and verify that they are working correctly. If you're having trouble, call Rick at heidenhain - 847-519-4858
  18. I actually had this problem a few weeks ago. I...

    I actually had this problem a few weeks ago. I turned the spindle manually for a few tool changes but it would always want to go back to the position that was not correct. I looked in my manual and...
  19. Replies
    17
    Views
    3,474

    That's what I did, and now tapping works like a...

    That's what I did, and now tapping works like a charm. The dwell time should typically be 0 right? I used 1.0 like in a program example from my manual and it worked OK until I did a deep tap and...
  20. I have parameter 4060.0 as X, 4060.1 as Y, 4060.2...

    I have parameter 4060.0 as X, 4060.1 as Y, 4060.2 as Z, and 4060.3 as 4th axis under the automatic lubrication section in the tech manual.

    4110.5,6,7,8 etc. are for PLC programmed durations for...
  21. Replies
    4
    Views
    784

    No problem, nice little refresher for me :)

    No problem, nice little refresher for me :)
  22. Replies
    4
    Views
    784

    Moment of inertia (I) = pi*r^4/4 Modulus of...

    Moment of inertia (I) = pi*r^4/4
    Modulus of Elasticity (E) for steel = 30,000,000PSI
    l = 30"
    P = 20lb

    I=3.14*.394in^4/4
    I= .0189

    Ymax=20lb*30in^3/48*30,000,000PSI*.0189
  23. Replies
    4
    Views
    784

    Sounds about right, 20 pounds isn't much.. Trust...

    Sounds about right, 20 pounds isn't much.. Trust your equations :)

    http://www.advancepipeliner.com/Resources/Others/Beams/Beam_Deflection_Formulae.pdf
  24. Bridgeport Interact 720VMC auto lube parameters

    I was adjusting my tapping deceleration and also looking over some other parameters in the technical manual when I saw the X,Y,Z and 4th axis automatic lubrication parameters. I have TNC2500 control...
  25. Replies
    17
    Views
    3,474

    I think values of .05 will work (.05V/ms) for...

    I think values of .05 will work (.05V/ms) for deceleration.

    http://content.heidenhain.de/doku/oma_controls/CD2/tnc/360/gb/thb360.pdf
  26. Replies
    17
    Views
    3,474

    Does anyone know the recommended numbers for the...

    Does anyone know the recommended numbers for the 3410 and 3410.1 perameters? I'm having this same exact problem, looks like they are both 0-1,999 (1.999?)

    TNC2500 on interact 720 with new control
  27. Replies
    6
    Views
    1,247

    From what I can tell tool #0 is imaginary. ...

    From what I can tell tool #0 is imaginary. Luckily my machines previous owner had etched the tool number onto each fork on the carousel so I know which one is which. It starts with #1 then goes up...
  28. Replies
    30
    Views
    8,578

    Heidenhain TNC360 post - doesn't work for TNC2500...

    Heidenhain TNC360 post - doesn't work for TNC2500 very well.
  29. Replies
    5
    Views
    1,176

    I measured the voltage between the case of the...

    I measured the voltage between the case of the control power supply (the multi voltage one) and it is 12v from + to ground and -12v from - to ground?? This doesn't seem right, but if I measure...
  30. Replies
    5
    Views
    1,176

    OK I got new FEAS power supplies with

    OK I got new FEAS power supplies with <2mv of interference. After finding the specs it looks like I needed at least <3mv and the cheap one I got was <120mv! I installed them tonight and I still get...
Results 1 to 30 of 70
Page 1 of 3 1 2 3