Hi,
We have an early model Mini Mill(2001). The machine will boot up and run, but in the middle of a cycle will shut down immediately without any alarm. It seems to happen when the machine is...
Type: Posts; User: Mike T.
Hi,
We have an early model Mini Mill(2001). The machine will boot up and run, but in the middle of a cycle will shut down immediately without any alarm. It seems to happen when the machine is...
Hi,
Would anyone have a photo of an older 2000 mini mill lubrication pump manifold/air/solenoid valve setup.
I re piped the air system so that the air inlet gauges and regulators are more...
Hi,
We have 2 matsuura 500 vmcs. One of them is having a problem with y axis OL alarm.
Sent the drive and motor out to be tested and both are fine. Re installed and still getting same alarm....
Hi, we have an LTC 10 AP leadwell lathe. We are getting a to Mis index alarm randomly. It will happen generally at any time during a cycle. I believe it to be a sensor, but do not know where to look...
I am in Boston,not crazy about the software either and bobcad was never helpful with this,ever. It is what we had so made it work. Let me know if you find it thank you
Hello,
We have been running BobCad V22 for several years. It isn't the greatest, and the support has been terrible from day 1, but we have made it work. The software crashed and we are not able to...
Cody,
Send me an email or fax # and I will send them to you
Hi,
Does anyone have a recommendation for relining a tumbler tub? I got a Burr King 45, but the previous owner had a bunch of different materials cemented around the tub bottom, including what is...
Hi,
I am looking to broach a square corner in A-36 Steel. The slot I am machining finishes 7/8 wide, 1-3/4" deep, 2" high. I am roughing the slot with a 5/8 rougher. I would like to cut the...
Hi,
I have a Leadwell MCV 760 XL machining center with a Fanuc 10M control. I have been dealing with a spindle problem where I only have 2 spindle speeds the first is if the programmed speed is at...
Yes, all of the data tables are entered. I have no idea what is going on with this machine....It was idle the other day when, on its own, the tool changer carousel started to rotate, the coolant pump...
Hi,
I have a Leadwell MCV 760 XL with a Fanuc 10M control. A while back, the machine had some problems and dumped the parameters. I was able to reload them and get the machine running again,...
Can anyone explain exactly how to reset the sensor?
Thanks!
Hi,
I have an older Leadwell VMC with a Fanuc 10M Control. I had been running the same part for quite a while and the machine was running fine. I programmed another job and noticed that the...
I have the data tables, I can fax to you if you send a fax #.
Hi,
I have a Leadwell MCV 760 XL and I dumped the parameters. I reloaded them, but there seems to be some kind of interlock that prevents the machine from moving. This happened a long time ago, and...
Hi,
I am in the process of building a 4 X 8 plasma table using precision plasma gantry & candcnc contols
I am looking for anyone who may have built one of these tables for ideas on how to deal...
Hi,
I have Bobcad V22. Just getting around to setting it up after a long time. I have it installed on my computer and am able to create a drawing, however, when I try to save the drawing to a file...
Hi,
I am usingBobCad V 22. When I try to save a cad file, the software shuts down. Can anyone tell me what I am doing wrong? Bobcad support USELESS!!
Thanks
This switch is mounted above the spindle- I believe it is relatively high pressure. I just want to be sure that it is not too much or too little pressure.
Hi,
I have been getting some good advice on an issue with a mini-mill low pressure alarm. The problem is with the pressure sensor under the front cover-just as I was told. I bypassed the...
Thanks Again!!
HELP!!!
I have a Mini Mill that is displaying a low pressure alarm. I have changed the regulator and am still getting the alarm. I have 120 psi at the compressor, and 85 psi at the regulator. Is...
Thanks, Got it back together,but still getting the low pressure alarm that I was getting originally. Changed the regulator,and have enough air pressure, but still no luck. does anybody know if there...
These pictures have been extremely helpful THANKS!!!
I still am looking for any idea where the low pressure regulator is hooked in. It is behind the panel where the regulator is mounted, but any...
Thanks, I hope that gets me started!
HELP!! I have a Haas mini mill. One of the guys in the shop took apart the Air regulators in the back of the machine- the incoming, the low pressure regulator,and the automatic lube manifold and...
Hi,
I have a Leadwell MCV 760 XL Vertical Machining Center with a FANUC 10M control. Recently in some severe weather, we had a power surge that damaged the electronics on 2 machines. The 10M...