Search:

Hi, I mean that I just drained a battery (condensers) on purpose to clear all parameters on these boards.

Just got back to the shop. Had reset NUMC and SPHC boards and do not know what to do further - it's just sends these errors (on attached photo) and i cannot clear them and go further than that screen...

Hi Guys,

having troubles with my Hitachi Seiki VK45-2 with Seicos control. The control does not start up saying NUMC_BOARD_SYS_FAIL . Then it shows "table checksum failed". I assume that the...

I dont usually do a necroposting, but in my case - all thermal overlaod alarms were due broken fan at the back of the control panel

Hi,

is there any way i can enable the DNC option (it says that option not found) or at least increase the memory capacity for my Hitachi Seiki VS50? Because it is a real pain to have a capacity of...

Hi,

i have a problem with my Hitachi Seiki vk45-2 . It showed today an error with some sort of "connection with the 4th axis failed". After examination it showed up with some components were...

Hi guys,

having some problems with '95 Mazak Super Quick Turn 18 MS and will be very appreciate if you help me:

1. First of all - subspindle is not in one axis with main spindle. When i grip...

I have taken these wires apart to get the oil running all the time. But the problem persists... How it can be so? Maybe the sensor is broken? But where can i look for him? There are not a single...

Yes, the problem is in the switch. I'm trying to find the proper replacement on a local market, can you tell me what is the working pressure ? There are digits from 2 to 0 and from 0 to 2, but i dont...

Hi again,

having a problem that a table does not come to an "old" zero in the middle. It's having nearly 3mm shift. I guess it became so after we have changed 2nd reference point for ATC in...

It began really annoying. Now it can stuck with error in a middle of a programm.
I have not such diagnostic screen (or maybe i cannot find it) so i just disconected the wires from the switch and put...

Thanks for the drawing.

I have set it to "0", but the problem remains. Maybe there's a real problem for a spindle lubrication? But if there were a problem, i think that it dont even start up...

The problem solved!

Have switched to maintenance mode, then activated maintence M-codes with M998 command and then by M-codes drove the ATC arm to its zero-position

Hi,

there's was a similar post already but it touches va55 only.

I have a similar problem, but i do not know how to properly get the manual control of solenoids.

The thing is - ATC arm...

The error alarm became more often. And can appear randomly during operation.
Can you tell me what is the pressure sensor look like and where is it situated? Thank you

I have a pressure gauge coming off the tank and its broken. But it was always broken, and error appeared recently

Thanks, I have seicos m3

Good day,

can anyone tell me what do i need to use a 4th axis on my machine? In terms of controllers. Are there any problems in initializing with the controller? Do i need to change the main...

Have used Mobil Velocite #6 but after 4 days the error appeared again ( Maybe wrong oil?

Thank you,

the control number is T1125704 . It has Seicos M-3. But i think i have found a problem:

I've checked the oil level in that rear tank and it was present, but i have mentioned that a...

Yeap, sorry, sn is 47103

Hi again,

my SN is T1125704

Thank for a promt response!

I will check it tomorrow for SN but it does not have a High speed spindle, due to my spindle revs are 8500 per minute. An as far as i know (i'm not in shop right now) -...

Hi guys

have a Hitachi Seiki VK45-2,

getting an error every time the tool changes: "Spindle lubrication distributor pressure low". But machine works fine if no tool change used. Does anyone...

Maybe User and Control panel manuals. Because i have only electrical maintenance

Have contacted them a week ago and got no response :(

Hi there,

just purchased Hitachi Seiki VK45-II and have couple of questions:

1. Does anyone have user manual for it?
2. How to change melodies for start and programms end?

BTW, very pleased...

Hi there,

what type of toolholder i can pick to replace my exisiting NT40 taper? Looking forward BT40 due its availability and wide range of metric models.

The main difference is the flange. BT...

Thanks, definitely right spot to choose milling tooling. But maybe there are also more complete places? Because I reside outside US, I will be forming a big package with air freight and will get...

Hi guys,
Can you share the link to online shops where I can get a complete tooling for Cnc milling centers. At least, chucks, fixtures, collects etc. And for some good brands, of course, like parlec...