Search:

Is it okay if the kflop is kept on, even though the engine is not turned off?

when restarting kflop and kmotion cnc, do count values in x display and y display keep previous counts?
or returns 0?

thank you sir, this is very helpful

I have entered the CH0 and CH1 axes in the C program,
questions 1. How to add command div C program? as :
when I click run:
bit 152, 153 turns on and DAC 1024 (5 volts).
then when the target is...

and this manual book is in pdf format.

below is the manual book for hydraulic and valve workflows:

pedal number 1 to start running the ram down, at the initial count Relays 1 and 2 become active so that the ram drops quickly, until the count approaches the material of about 10 cm Relays 1 and 2...

this is the diagram i got from the machine.

The following is my research, on my normal or original press machine:
There are 5 relays to activate the valve
Relay 1 = valve for fast descent Axis Y1 (not valve proportional)
Relay 2 = valve for...

these are today's test results. for the results when the ram is down, it is very perfect, and the movement is smooth, the right axis (CH1) and the left axis (CH0) are very synchronous, the size is...

for SIZE, is it count / inch or count / mm?

this is a picture of my laptop, because now i am at home. tomorrow start retrying according to what you suggested yesterday.

I don't understand how to determine the slave gain for CH1 (master) and CH0. in your opinion, how much should it be in?

Please correct if it's wrong, if I click MOVE, the axis moves towards the...

43 cm or 430 mm



maybe i am wrong in measurement, because linear encoder is very sensitive. you're right about 200.



because when the ram drops, the hydraulic CH0 (slave) drops faster...

Which channel should I change to Slave Gain -1?

and this is the filter screen CH0 and CH1. and the response step.
for encoder counts from top to bottom = 0 to 47000 counts.
yesterday I measured with a ruler, for 1 mm = 170 count.
but I still...

This is the image for the CH0 (slave) and CH1 (master) configuration.

Please correct me, if I am wrong.

speed to move towards the target. if wrong please correct.

i try :
P= 1.6 I=0 D=0
output=2047
integral=200
error=100000

V=400000
A=40000

please teach me how to set V, A and J.

this is a plot image, what's wrong with this.
ram can hold the position, but ram Y1 with Y2 difference of 4mm.
I made Y1 the master. Please help.
what should i change?

this is data from my linear encoder LS 623 HEIDENHAIN

100/mm

just now, I can already test 2 hydraulics. but the plot results are not perfect. the value for V A J is still I'm looking for. as well as P I D. I need information to determine it.

how to test with 2 hydraulics?, because if only one, it will be skewed. and a little dangerous.

can the Configuration & Flash output 2 DACs?

how to test with 2 hydraulics?, because if only one, it will be skewed. and a little dangerous.

51/5000
this is a diagram of my engine's valve and oil flow.

yes, Y1 Y2 valve which performs rising and falling. direction up and down direction.
and a pressure amplifier to adjust the pressure.


Pressure DAC (+8 volt).
hydraulic valves(Y1= 3.4 volt ).
...

recently I tried moving the CH1 axis, and it managed to go up. but to move down, still can't. and a new problem, the axis can't hold the position, always moving down by about 1mm / minute.

when...

that's right sir


If RAM is not able to press / bend the workpiece, valve proportional for pressure will be increased to increase the pressure automatically.


Step Response for the / ch axis...

this is my first job. does anyone have an example c program for press brake with KFLOP + KANALOG board?

I have connected the KFLOP + KANALOG to the press brake machine. and I've tested the input...

oh ... my god, i just got it now. meaning z0 is starting from the top, or the beginning of the RAM position is above, and must write G21 first. I'm sorry sir, because I don't understand the article...

G0 z1000
G21 (mm mode)
G1 Z500 F100 (Move down at 100mm/minute)
G1 Z250 F50 (Move slow down at 50mm/minute)
G4 P2 (dwell 2 seconds)
G1 Z1000 F200 (Move back up at 200mm/minute)
M30 (end)
...