506,499 active members
3,039 visitors online
Register for free
Login

Search:

Type: Posts; User: ROBBY 68

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: FANUC DOWN AGAIN. 914 RAM Parity Servo OM-B

    Hello Sir
    I have same 914 alarm on my Takisawa Tap center OM FANUC
    I have lost memory due to low battery, but now I’m getting 914 alarm, if I reset memory
    920 watchdog alarm comes up..
    Could you...
  2. Replies
    11
    Views
    3,315

    Sir I've seen same issue on some ST machines,...

    Sir
    I've seen same issue on some ST machines, double check parameters for X axis.
    There should be a thermal compensation value that isn't right.
    Ask the Haas guys to verify this for you against...
  3. Replies
    10
    Views
    4,729

    Setting 23

    There is setting 23 ON/OFF , it makes visible all 9000 prgrms.
    There you can figure out
  4. Replies
    10
    Views
    4,729

    There is setting 23 ON/OFF , it makes visible all...

    There is setting 23 ON/OFF , it makes visible all 9000 prgrms.
    There you can figure out

    - - - Updated - - -

    There is setting 23 ON/OFF , it makes visible all 9000 prgrms.
    There you can figure...
  5. Replies
    15
    Views
    1,303

    Mike Perhaps your machine has counterweight? If...

    Mike
    Perhaps your machine has counterweight?
    If it's 19 years old, counterbalance was not released......
    If you see chains above Z then has counterweight.
    And no need to block, spindle may move...
  6. That is correct, And movement is because it...

    That is correct, And movement is because it references Z0 (work offset) prior going Z home.
    Adding G91 you command incremental move.
    Robby
  7. Replies
    18
    Views
    950

    Thanks Beto! Regards Robby

    Thanks Beto!
    Regards
    Robby
  8. Replies
    12
    Views
    1,117

    You should double check your PMC parameters....

    You should double check your PMC parameters.
    Because lubrication on and off is set on timers,
    Perhaps a wrong value inserted?
    On some FANUC 0 is not possible to see ladder
    But diagnostic soft...
  9. Replies
    18
    Views
    950

    Beto You were able to find encoder? If so,...

    Beto
    You were able to find encoder?
    If so, where?
    I need same part.
    Appreciate lead.
    Rooby
  10. Replies
    7
    Views
    428

    Did you try M41 (Low) or M42 (High)? just in...

    Did you try M41 (Low) or M42 (High)?
    just in case
    b4 commanding speed
    Robby
  11. Replies
    7
    Views
    428

    How do you command speed? MDI S1000 M03; I...

    How do you command speed?
    MDI
    S1000 M03;
    I understand manual mode spindle rotates?
    if so, are you able to see speed on screen?
    get any alarms?
    is there a trassmission?
    do you have to command...
  12. Replies
    7
    Views
    1,231

    What kind or Brand of Rotary table do you have...

    What kind or Brand of Rotary table do you have assembled?
    Model?,
    Regards
    Robby
  13. Replies
    6
    Views
    350

    G50 S3000, You are "telling" the machine is the...

    G50 S3000, You are "telling" the machine is the highest speed you can reach.
    Because G96 is a Constant Surface Speed and according to Diameter being cut
    As much as X axis is travelling to center of...
  14. Crandolph Nice Job! What brand of plasma are...

    Crandolph
    Nice Job!
    What brand of plasma are you using?
    I like to start my own soon.
    And need all advises possibble.
    Doing a little research and gathering experiences.
    Thanks in advance.
    Robby...
  15. Replies
    6
    Views
    740

    Hello Out there! If someone has Miyano TSV 23...

    Hello Out there!
    If someone has Miyano TSV 23 Parameters
    It will be greatly appreciated.
    I only have 900 parameters.
    Regards
    Robby
  16. Replies
    30
    Views
    5,209

    Hi Yes, inside MPG check wiring It works with...

    Hi
    Yes, inside MPG check wiring
    It works with 5VDC and It should be generating pulses backwards.
    Correct wires. Positive pulses Up move / negative down movement.
    Robby
  17. Replies
    6
    Views
    740

    Handasse I have found what you need for...

    Handasse
    I have found what you need for interface with HAAS 5C
    Attached check drawings.
    you can use M20, M21, or M22. for program.
    you have to have TB1 which is optional M code relay
    signal is...
  18. Replies
    2
    Views
    654

    It should be a Viscosity Grade 32 which is...

    It should be a Viscosity Grade 32
    which is Hydraulic oil.
  19. BB I have been able to isolate all interlocks...

    BB
    I have been able to isolate all interlocks and cycle start with success!
    there is only one thing left.
    When command G01 move, cycle start lits but No move, No alarm, just stand still.!
    I know...
  20. Replies
    6
    Views
    740

    Hello Handasee I will attach a picture of board...

    Hello Handasee
    I will attach a picture of board you might have on your machine.
    There are two ways you can work with this unit 5C on your Miyano.
    As I mention with your controller box is possible...
  21. Replies
    16
    Views
    652

    Hey Buddy I would swap Z axis Motor complete...

    Hey Buddy
    I would swap Z axis Motor complete from the other SL 2B
    90 % you will solve it there.
    Reading the whole story it seems as Encoder problem, because normally at lower speed you can rapid...
  22. Does anyone has parameters for a Miyano TSV 23?...

    Does anyone has parameters for a Miyano TSV 23?
    Control FANUC 0M
    Thanks
    Robby
  23. Replies
    6
    Views
    740

    Hi Do you have the controller box for the 5C?...

    Hi
    Do you have the controller box for the 5C?
    Robby
  24. Replies
    16
    Views
    652

    I will suspect of Power supply. On Electrical...

    I will suspect of Power supply.
    On Electrical cabinet you have it on left side.
    Control for PS comes from a slim relay board mounted on left door
    Same cabinet.(bottom of memory boards)
    Perhaps...
  25. Brendan Do you have Electrical wiring diagram?...

    Brendan
    Do you have Electrical wiring diagram?
    I have an SL 2 and NO documentation, I pass thru all story you mention on your post
    Now I am at point of moving axes and home correctly.
    But still...
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4