584,805 active members*
5,018 visitors online*
Register for free
Login

Search:

Type: Posts; User: gabedrummin

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds; generated 16 minute(s) ago.

  1. Replies
    2
    Views
    1,177

    Re: Hitachi H-Cut 203M Alarm

    I suspect if its a machine with a 6m controller your U-Axis resolver is starting to have an issue . I would go into the paramters tell the machine its a 2 axis machine and see if the issue gose away .
  2. Re: How long does it take to learn to feed G-code through a machine?

    Depending where you live a lot of colleges offer cnc programming course 40 hour crash course took mine in 86 ish .
  3. Replies
    1
    Views
    1,032

    Re: X-AXIS GEAR DM3000

    Never mind I did a timing belt conversion .
  4. Replies
    1
    Views
    426

    Re: Fanuc OM-A Display Issues

    Seems to be related to the cold last couple of day temp has been 70 plus and screen lights up first attempt . I did not think a lcd screen would be suspect to temp or maybe the crt card is ?
  5. Replies
    0
    Views
    676

    MODEL O ELOX/ FANUC DISPLAY PROBLEM

    Machine has has a Fanuc 0M -A control . One of the first Elox/Fanuc machine to go with ac servo drives .Machine had a 14 inch color CRT originally .Many year's ago I replaced the CRT display with an...
  6. Replies
    1
    Views
    426

    Fanuc OM-A Display Issues

    Many year's ago I replaced the CRT display with an LCD conversion .And it has worked perfectly for a long time . Lately the screen wont turn on and I have to repeatedly turn it on turn it off and...
  7. Replies
    1
    Views
    1,032

    X-AXIS GEAR DM3000

    Can any one tell me the pitch and gear count for the x-axis gears that drive the x-axis lead screw .Thank you in advance .
  8. Re: Old Fanuc Tape Cut w0 freezing immediately on bootup with a memory dump screen

    The only parameters that will not auto load are the ones for the digital AC servo drive .Brake motor tension settings . Com. settings. Edm cutting settings . Do you have a manual for your machine...
  9. Re: Old Fanuc Tape Cut w0 freezing immediately on bootup with a memory dump screen

    If the batteries go dead while it was sitting it will lose all its parameters . Change the batteries while the machine is turned on .

    Memory short cuts.

    Memory all clear Hold 0 and delete...
  10. Replies
    22
    Views
    2,224

    Re: Acorn isn't closed loop?

    Acorn is a motion controller .It will send the step and direction signals to the driver . In a closed loop system the controller will correct the step train to make sure a step is not lost . Even if...
  11. Replies
    3
    Views
    2,293

    Re: Custom thread adapter

    How long is it ? Dimension from end to slot ? Taper at what angle ? Dose it need to be concentric from thread to thread ?
  12. Replies
    5
    Views
    1,288

    Re: Fanuc A0-1 cutting stops or fluctuates

    If you don't have the cutting data tape you will have have to enter the cutting conditions thru MDI .
  13. Replies
    5
    Views
    1,288

    Re: Fanuc A0-1 cutting stops or fluctuates

    How is the water condition ? Have you used wire machines before ? It is a slow process, water condition, guide condition, power feed contacts all have to be in proper condition .Start there.
  14. Replies
    0
    Views
    758

    TOOL WEDGE CLAMP

    Looking for dimension for a tool wedge Hurco cnc lathe TM6i Thanks if you can help.
  15. Re: South Bend Magnaturn 612 wanted for CNC conversion

    Good luck. I've been looking for one for years . Have seen 3 for sale in the last 10 years and very pricy especially now that everything has an inflated price good luck sir. I settled on a Dayna myte...
  16. Replies
    6
    Views
    1,715

    Re: Quill fit upwards tolerance, opinions???

    [QUOTE=rolfinator2002;826597]Thanks for all the feedback. I'll consider the topic closed then. I think I'll let it fly, and if I get errant finish or dimensions, then I'll rechrome the quill and...
  17. Re: NEED HELP! Fanuc error 337 U encoder won't reset

    IF YOU DONT NEED TO CUT TAPER GO INTO PARAMETERS AND TELL THE MACHINE ITS A 2 AXIS TURN OF U AND V AXIS. THEN SEE IF TI WILL RUN.
  18. Thread: MPG-16

    by gabedrummin
    Replies
    3
    Views
    2,217

    Re: MPG-16

    After 6 months problem has been traced to defective motion control card .
  19. Replies
    3
    Views
    1,705

    Re: Machine Simulation

    Your machine not the correct scale .If its drawing in inches it needs to be drawn in millimeters.
  20. Replies
    5
    Views
    1,234

    Re: DM3000 Z travel distance?

    MY machine has about 8 inches of z with the tail stock on and about 12 with it off .
  21. Replies
    5
    Views
    1,234

    Re: DM3000 Z travel distance?

    It will travel to the right until the carriage hit's the limit on the back side of the bed . It will travel z- till it crashes into the chuck if you don't stop it . So the limit switch on the back...
  22. Replies
    5
    Views
    1,234

    Re: DM3000 Z travel distance?

    With or with out tailstock ? What type of chuck , center, collet chuck are you going to use ?
  23. Replies
    2
    Views
    2,508

    Re: Harig 6x12 hand feed grinder

    I was thinking the bearings should be installed like this ?488586
  24. Replies
    2
    Views
    2,508

    Harig 6x12 hand feed grinder

    I want to replace my spindle bearings . I know don't do it .But I have a plan . Taking it apart no problem. Re-assembly will be done inside a large plastic bag . I will put the spindle shaft in the...
  25. Re: Pls give me some feedback on my drawing die plan...

    You are going to need some type of press to do this .Weather is a mechanical or hydraulic you need something to mount the tool in . And drive the upper down or drive the bottom up or both moving...
  26. Re: Pls give me some feedback on my drawing die plan...

    What will generate the fixed spring pressure ?Are going to try to bolt the blank holder and lower die together with material in between ? Most dies we run 3000 + tools we maintain pressure between...
  27. Re: Pls give me some feedback on my drawing die plan...

    You better get some springs in there . If you see wrinkling on the finished part that is caused by not having enough pressure between the blank pad and die face . you might need some stand off to...
  28. Replies
    2
    Views
    1,803

    Re: Bridgeport mill table screw movement

    That is a safety handle for the power . It can be replaced for a standard handle.
  29. Replies
    17
    Views
    3,952

    Re: Cutting taper with Fanuc Robocut

    485794485796 This cuts taper .
  30. Replies
    17
    Views
    3,952

    Re: Cutting taper with Fanuc Robocut

    In your first post there are two pics the one on the right . The settings page thats where the problem is .If I remember I will take a pic of mine . I made a program to cut taper and had some...
Results 1 to 30 of 402
Page 1 of 14 1 2 3 4