584,833 active members*
5,667 visitors online*
Register for free
Login

Search:

Type: Posts; User: peakcnc

Search: Search took 0.00 seconds.

  1. 1997 daewoo ace-h50s cnc - looking for manual

    wondering if anyone out there has a manual to sell for a 1997 daewoo ace-h50s?
  2. Re: ch250 hicell bar puller programming??? need help.

    rookie mistake, didn't have sensor on back of draw tube set correct. machine wasn't reading that the chuck was open
  3. Re: bar puller code? Hitachi seiki CH250 super hicell - seicos control... need help!

    figured it out, sensor on back of draw tube wasn't set right for open jaw. all good now!
  4. bar puller code? Hitachi seiki CH250 super hicell - seicos control... need help!

    I have a CH250 super hicell. picked up a bar puller and turret won't move after opening spindle, i'm guessing that I am missing an 'M' code or perhaps a parameter is missing?? I've attached my...
  5. ch250 hicell bar puller programming??? need help.

    I have a CH250 super hicell. picked up a bar puller and turret won't move after opening spindle, i'm guessing that I am missing an 'M' code or perhaps a parameter is missing?? I've attached my...
  6. Replies
    2
    Views
    1,251

    Thanks for reply Jim. Table is a fastcut g5 with...

    Thanks for reply Jim. Table is a fastcut g5 with water table running dynatorch software. Had a friend with more plasma cutting experience than myself help out yesterday. Made a few changes to...
  7. Replies
    2
    Views
    1,251

    hypertherm 1000 g3 scaled arc settings??

    Having issues with plasma table. Using a hypertherm 1000 g3. Scaled arc voltage on plasma table was set at 5volts. Looking in manual it says "full arc voltage. No voltage divider. 300vdc maximum....
  8. Replies
    0
    Views
    3,801

    torch not touching off part?!?!?!

    New to plasma here. Have a fastcut 5x10 table and using dynatorch 3.6 software and hypertherm 1000 g3 power supply. Been using for 2-3 weeks now and been working pretty well. was cutting 12 gage and...
  9. Replies
    0
    Views
    713

    hypertherm 1000 hookup to plasma table

    I just picked up a used fastcut plasma table. I have a g3 1000 that I'd like to hook up to it. Looks like previous owner had a powermax 45. There are two wires hanging off the bottom that he had...
  10. Re: problem!! spindle issues and fadal feed over ride dial not working

    Been away for a couple of weeks, had service guy in and he looked over wiring and checked/cleaned up behind monitor. Feed dial is working again! Guessing lose/dirty connection somewhere. Will see...
  11. problem!! spindle issues and fadal feed over ride dial not working

    Been having spindle issues last couple weeks. Ended up replacing encoder, prox switch and damaged draw bar. Spindle seems ok, not like it was so not sure if service guy missed something somewhere? ...
  12. Replies
    3
    Views
    1,278

    lathe c axis new plane

    I always get lost when doing this. I have a hub that I need to drill/tap and mill/bore a hole in. I'm having issues getting the bored hole at the x+ position so that I can mill it, lathe has live...
  13. Replies
    4
    Views
    1,278

    Re: z axis resolver adjustment - 2000 4020h

    well hopefully this will help someone else down the line.
  14. Replies
    4
    Views
    1,278

    Re: z axis resolver adjustment - 2000 4020h

    ended up using the Axis Current Survey Settings to adjust Z. seems to be working so far. I attached file as to procedure. Maintenance guy I had in said he used this to set Z after he replaced...
  15. Replies
    4
    Views
    1,278

    z axis resolver adjustment - 2000 4020h

    Had some service on machine last week when I was away, replaced z axis bearings and a few other things. spindle is now too low when I do tool changes and pushes tool out of grippers. manual says to...
  16. Re: Can i buy a damage Hitachi Seiki Ch250 Lathe Machine(Seicos 18T,2 Spindles,2002)

    done!
  17. Re: Can i buy a damage Hitachi Seiki Ch250 Lathe Machine(Seicos 18T,2 Spindles,2002)

    highjacking this thread, hope no one minds. I have same lathe and having an issue with it. I'm guessing you are familiar with these John? If so can I bug you for some troubleshooting help...
  18. need help hitachi super cell MILLING SPINDLE POSITION ERROR #2140

    Just moved machine into shop a couple weeks ago. Was having some issues with tool change and home position. Machine came with low batteries and was getting alarm for that, think it was ATC battery...
  19. need help with communicating to mazak m32 - eia

    So I just picked up an old h500 with m-32 control. Previous owner was able to send EIA programs back and forth, they had it hooked up direct to computer. I'm using DNC one reader ---...
Results 1 to 19 of 19