Search:

adjust the 3 pots on the amp card (adj the comp pot)
turn cw and you hear a noise on the motor,back 1 turn and dessapear
do this to the 3 axis ok ...good luck

check or adjust the encoder of the z axis (is on the top of the machine)
also change the position of the amplifier (the z is on the down position)
good luck

mi ez-path romi: when i make an event and try to run ,dont move nothing !!
the machine goes to home and everything looks fine
what can i do?does anybody has had this problem

i think becouse ,i can change the loc to remote on the driver,does anybody know how to do this?
or maybe another reason why dont run?..(i put 15 hz on the driver and run) thanks in advance...

turn the jog pot to + and push escape at the same time,now the machine are in home mode

x axis fault,i change the driver x on z and still the fail,check the motor impedance too (no short),limit sw tooi have a relay cr6 (lube motor) when i put in place,the breaker cb4 comes down(have...

we buy a yushin HOP-ii robot,but have broken wires,does someone have the manual
and or the diagram of the connections..thanks in advance

in the monitor are a little coil,next to the fly back...try to adjust,but take very care becouse are high voltage
with a litle hex screwdriver,also too check if the capacitors are busted if are...

make a resoldered,to all the board,and check if one of the capacitors are busted....good luck

Hi,to all the peorle....i want to know how can i do to take off the alarms on the dm-800g from mitsubishi cnc
so,i push the reset botton and still apearing,1)3-ATC-NOT READY...2)4-CL/UCL-SW...

look like dont have power the motor,when put the cutter work so slowly
i want to know how adjust the clutch...thanks in advance

the TDA1175P is a circuit (16 pins) it is the video amp.change it,i have done many times...good luck

ok,i need the E-PACK floppy for fx20,can you send me a copy to [email protected] in advance

after you repair the unit(change the mosfets n-channel)must be the same impedance for all ok)install and adjust the amp.turn the compensate pot ccw all,them back 1and half you gone a hear the servo...

i am in cd juarez mex.but you can send me the floppy data for e-mail,
[email protected] in advance,by the way....do you know
why the fx20 dont want to burn,maybe the wire need...

yes i do,and change the solid state relay too,the bridge of diodes is ok,becouse the amps dont have voltaje (165 vdc)
i put a jumper on k2 to the control line #8 and they turn on,but no make any...

originaly the machine was runing a program,sudenly the machine go to fault and stop everyting
now i cant move nothing,and appears x,y,z,amp fault.....what can i do?

x,y,z fault on my vmc4020 the amps dont turn on
change the ss relay,bridge,but still the fail...
any suggestion...thanks

sorry,put #1,+input,this will turn the red bar on green,whith this you can continue....
the E-PACK floppy drive is not for that

put the fx on the maint screen,select the clean seal plate with the purple cursor and chage the parameter to 5000,then enter
you will see the red bar change to green,all must be on green to continue...

now fix it.....was the driver configuration

the spindle turn very slow,even in high speeds on mi fadal vmc 4020
i change the spindle card from other working good,but still the problem
any suggestion on that fail will be accepted..... thanks

:violin:

and i did everyting....now mi fail is:C AXIS FAULT,error #9,spindle fault line,do you know someting abaut it?
i appreciate your aid..thanks again

thankyou for all,when you need some tips,maybe i can helpyou....see you body

no dont have,just x,y,z...i know,when the A axis install,i have to put a connector and a board,and a valve too on the rear of the machine
i was making in other machines,as you see i am almost an...

1)yes,2)yes,3)1997,(mod 906-1),4)can be any,depends in wich the machine are working at the moment.5)yes
6)no the jog dont work when the machine stop(i have to reset the sw-red to work)and then move...

no,the way lube is one thing and the spindle use a cooler to discipate the heat and a fan too,but the fail is not in the spindle
the machine stops in any axis (when the fail comes)can be x,y,or...

try autotuning the motor with the baldor driver,put a 60 hz frequency and let syncronyce themself
can be the regenerative resistor too...good look

no,but i check all,and look like the oil valve is not working good,becouse i put a jumper and work(is just a switch) but i dont know why stops in the middle of the job