One other notation on these motors... They have 4mm shaft..I was able to fashion a bushing to allow the 5mm to 8mm couplers by heat shrinking tubing to the shaft. turns out they are perfect fit now.
Type: Posts; User: blackbeard52
One other notation on these motors... They have 4mm shaft..I was able to fashion a bushing to allow the 5mm to 8mm couplers by heat shrinking tubing to the shaft. turns out they are perfect fit now.
Received some great Nema 17 motors Yesterday. here are the specs.
These are nice 6 wire 1.8 degree stepper motors.
Type 103H5208-0842 or -1241 or -0841
NEMA 17
Sanyo Denki
today I finished testing the electronics for the steppers and SD ram.. I cheaped out and ordered from Ebay / China the ramps board and drivers as well as the sdramps card.... after two days without...
looking back I could have made this a bit more user friendly for those not having a milling machine to cut the v slot. I noticed some 3/4 or 1/2 inch aluminum angle at the Home Depot that would...
Well I scrounged some nylon plate from a scrap bin at a local salvage. Piece is 1x4x12inches. so I have began to machine the x axis. I purchased some O-1 drill rod from Mcmaster Carr as it seemed to...
Oriental Motor Company Vexta Model C4041-9012/328288-01-A
Specifications:
7.2 Ohm/phase, 4-wire
A 2 phase 1.8 deg/step 5.3 Volt 0.75 Amp stepper motor.
Does anyone know the holding torque of...
Well scored a bunch of old HP plotters... unfortunately after tearing into one of them I found there is not any usable parts for this build...not one rod or stepper... only was able to scrounge a...
I figured I would come back into the scene ..As I havent been here for about 3 years. I began to have an interest in 3d printing so I figured I would give it a try. Especiall since I found this very...
Scott and Pete
I will check the availablity of a local Blount county meeting place. I would like to start by going to local area machining or molding shops to get interest there..what do you think?...
Khalid
Man I take a little break and you reinvent the world.... Super work on your program... If you need web space for your design or files and/or site just let me know... I cant help with...
All those puzzles usually have a sheet with all parts in them...you can scan them to pdf and make a dxf that way.
B
Removed after it was found to be a combination of two dino's... Sounds like some of my friends
Bob
Oh yeah and some free embroidery software!!! http://sophiesew.com/
Bob
Wow Khalid you are really engineering this thing... I thought we were going to make it KISS (Keep It Simple Stupid) machine... I have been viewing the video of the machine that inspired this venture...
http://www.cnczone.com/forums/showthread.php?t=5276&page=14
Happy cutting
Bob
http://www.cooperman.talktalk.net/files/18.htm is a low powered laser .... it is not copper vapor laser...it is built out of a salvaged DVD burner... maybe a better high school level project.
Bob
Details?
I must have issed the narrative and photos...
Bob
Bill
Since I didnt have any experience with clock building I ordered the gears laser cut so the mesh would be more accurate... Glad I did, It took me a month to cut and finish the other pieces......
Bill
How ya doin...I built one of the clockworks clocks a few years ago...
Bob
I have access to some 29a55 controllers and I have 34d106 stepper motors and would like an opinion if these would be compatible...from my research they are but its nice to have verification. I have...
The most likely cause is backlash... If your AB nut is that sloppy replace it... it also could be caused by loose connection (set screw or loose lovejoy) however the measurement would vary ever so...
Only if it is consistently this measurement.....
Thought you might like this clock
http://www.scrollsawer.com/issue26/woodengearclock.php
Bob
IMHO the v groove gives a wider range of rail configurations. With the u groove you would most likely have to use a precision rod instead of a off the shelf hardware angle iron. Using the angle you...
Yes that is right... Also I remembered these do not do network at all...at least according to HP see...
null modem cable is for rs232 port....Sorry Al for jumpin in... One thin you could do is to purchase a PCMCIA serial port available at...
rgoldner
let see some chips flying off that new axis and some impressive turnings..
Bob
Actually I didnt... I have tabled the use of the drives until I get servos that will work with these drives..
Bob
Shandley
the file is listed in post #57 you can download it from that post....
Bob