Search:

I working on an older Toyoda model 450 and I would like to probe the fixture and set the work offsets. Would anyone offer some incite into how to do this.

Anybody have Ideas or anybody had this problem after crash. Machine crash and now my turret will not seat completely down to compress the coolant connect. It seams to be 1/4 to 3/8 from bottom....

I recently had issues with my machine not moving, tried to rotate tool arm manually thinking that may have caused it due to it maybe out of sequence and then that became stuck in with tools in it. Oh...

Thanks for the info. I have a OSP7000M control if that helps..

Not locked not that I know of. Panel responds as it should. no fuses I can see popped. I put in a tool change in MDI and you can hear it want to respond but no hydraulic movement. tool will grab if I...

No not that I know of.

Turned on machine ran through its checks all looks fine, press power on the control control fires up hydraulics same, but machine will not move. Hydraulics at pressure and oil, chiller the same, air...

Thanks for the info... I will let you know how it turns out...

I have a 1990 LB15 with a 5020L monitor that finally went on the fritz.. Looking to see if there is any new options available out there. CRT is the only thing that's on the fritz. Data shows but very...

Thanks

Thanks Wade, I will look into that. I had the machine running fine last time out but it sat for some time I'm talking days not months. I did erase the offsets for tool 1,2 & 3 as I was setting up new...

Would anyone have a current list of error codes for a OSP 5020L turning center. I'm getting a 266 A when I try to MDI into high gear and a W07 D VAC motor not reedy to start when I try to jog the...

My apologies I did not include the controller model number OSP5020L on a 1990 LB15

Can anyone assist me with the correct configuration to make a back up copy of my machine settings in case something causes it to delete all operating files needed to run. Purchased this machine with...

I have a Floppy Disc drive in my control panel I want to replace it with a USB emulator in its place. I need a emulator Model No#?? and wire/pin configuration ?? that will work. Wire Diagrams,...

No looking to convert to USB I have a floppy.. Looking for the right set up that proven and how to do it.

I have a 1999 Okuma MX 45VAE w/OSP7000M control with a Floppy drive and I would like a conversion to USB if possible, any directions or suggestions??? Any help is appreciated.

Would anybody have the correct pinout guide or layout for Okuma OPS 5020L ,7000m controllers to build a transfer line. This is for pinout transfer and receive directional ?? 1st diagram is example...

I have a 1999 MX 45VAE with a 3.5 floppy drive wondering if anybody has a solution to convert over to USB without going to Okuma or distributer

Does anyone have the correct set-up to download programs onto my 1990 LB15 lathe with a 5020L controller. I have been reading all the posts here but they all are from back in the day 10yrs plus....

Does anyone have the correct set-up to download programs onto my 1990 LB15 lathe with a 5020L controller. I have been reading all the posts here but they all are from back in the day 10yrs plus....

My machine is a LB15. Yours may be close or even something to compare to anything would be a help. Okuma or my local distributor doesn't offer much support.

1990 LB15 Hope that helps...

Model Okuma LB15, 5020L control

Would anyone have any copies of the wiring diagrams for a Okuma LB15. Need to use for some upcoming maintenance..

Thanks..

Thanks for the reply.. Question is where and what do I change...

- - - Updated - - -

Question... What are the M codes...

[email protected]

Any ideas I cannot got my tailstock to move out on my 1990s Okuma lb15 with the peddles. Don't know if there is a command to input or unlock. Petals, cord switches all check out it just doesn't...

Thanks for the info..... Problem solved today... As I stated in my earlier message my machine was sitting for several years prior to my purchase. This caused the fluids in the head casing to thicken...